Search:

Toe jacks and a few others beat pry bars all too.My machines range from 300 lbs up to 7500 lbs dont move them often but occasionally need to make more room.
Dad and I moved a few sheds and dead...

I thought last years would be a little bigger than this but you are probably right.With those little legs it was a chore traveling the 75-80 yds from the ditch across the road to where they are now....

Ive used the track style and they were good but for my hobby shop these do what I need and not cost a couple thousand dollars.

If you grout in the saw cuts or cracks these are good. Or even a...

Measure it out today and if I think its needed I can add a 3rd axle and 4 more wheels on each skate.

325841

Machine skates Im working on drilled the bodies and swivel plates for the pins welded pins in cleaned up faces and fitted today. Still have to cut in the flat bearing races between plates...

We had a shop here the owner built up was all big machines his brag was we can do what few others could. His band saw blades were 1 1/2" thick. Arrogant and self centered no one could be around...

Venting will be important. As will temps. fill from heavy end to light so the added weight helps force the material in. A lot of moulds in industry settings are pressure cast with a shot tube. This...

I believe the same process could be used on most presses to convert. A round plate to fit the shell holder cut and a 1 1/4"12 threaded replacement bushing for the top or 7/8 14 for the top, on some...

Today was another little one enjoying the rain was a little smaller than yesterday. Not sure how many eggs they lay in a group. Or what the average to hatch are.

I have done it in a croc pot, I wrap the fats / trimmings in cheese cloth add water and cook down. The clean fat will float let cool and it can be lifted off and dried. The cheese cloth holds the...

Wait till one that size wants to climb in the canoe with you. :(

We cleaned them and cut up into pieces along with the straps inside the upper shell. browned and fried it like chicken. was a very good meal. We would catch them in the sand bottom ditch on the...

Top dead center appears to be a priming ram for a press
bottom dead center looks tro be a puller used in fixing watches.
right appears to be a deburring chamfering tool.
On the left I dont know

Just for a size comparison he was bigger than a quarter and smaller than a 50 cent piece.

Coarser gives a better grip but dosnt show the grain as well coarse can become uncomfortable in a bare hand. Finer will provide grip shows the grain better and is more comfortable to the bare hand. I...

This little guy was on the drive when I came in from the shop today Looks the the snapping turtles have hatched this year.325764

Lightly square the crown this will give a solid zero ( especially if you have a dro) to work from. Then when done put a nice crown on the muzzle. If enough room you could even recess it a little....

The buried 100 dollar bill hasnt lost value it has lost buying power. It takes more to buy the same

I believe the one on the right is a hang on weight for a disc or other implement.

Watch out for the Tap Magic ultra thick it will discolor and cause rust. The old tap magic ( peppermint water) would when used on stainless.

One of the best I have found is anchor lube its a great...

Machineing shops are even getting hit by the epa do to the oils, coolants,and solvents being deemed hazardous materials.

Something to give some perspective. Dies, shell holders are manufactured to upper end tolerances, gauges and chambers to min specs. I have had tight chambers cut that had to have .010 faced of the...

That much sticking out (rim is roughly .050 on 308) is more than likely a difference in the body tapers. Even machine gun brass would have that much excess head space. a few thousandths on the body...

I use the counter bore does the same as the case trimmer and shaft but has better chip clearance/removal.

Back around 1976 I started in my first job shop ( it was a small 2 man shop) I dont remember the wage but the Boss brought out the second check and tolkd me therees a .20 raise on this one. Eddie...