I've cleaned several rusty molds by soaking them in bore cleaner or WD-40. Then get a nylon bore brush and some fine steel wool and chuck it into the drill and clean
the cavities. It's worked for...
Type: Posts; User: Nick10Ring
I've cleaned several rusty molds by soaking them in bore cleaner or WD-40. Then get a nylon bore brush and some fine steel wool and chuck it into the drill and clean
the cavities. It's worked for...
Forum: Casting Equipment
I've had both LYMAN and LEE. The Lyman is a MoldmasterXX and it is great. I also picked up a 10 pound Lyman Ideal(it's old ) but it still works.
Like other people have said the LEE is a dripper.
...
Forum: Cast Boolits
I had a LEE 148gr. wadcutter TL mold. When I first started casting the wadcutters I sized them .357. The groups from my 2 PPC revolvers weren't
good at all. I then sized them .358 and it was as...
After thoroughly cleaning the mold of all carbon from smoking them I coat them with a rust preventitive
and then wrapped them in a plastic baggie. They are then stored. I have never had to clean...
I had a mold that resembled the one in the picture purchased at a garage sale. I soaked it in WD-40 then got a bore bruch wrapped in fine steel wool and
ran it in each cavity until clean. I then...
Forum: Muzzleloading.
I got a Lyman .54 MAXI mold for my Renegade and have had good results with Pyrodex powder.
Forum: Muzzleloading.
I have a round ball,REAL bullet and Lyman Maxi mold for my .54. If you get a good rhythem going you can cast a large quantity in a short time.
If you use 2 molds at once and keep the pot supplied...
Forum: Gunsmithing Tips & Tricks
I've gotten ridges out with a lead remover I got on line. It's metal shavings like those on a scouring pad. You wrap a few strands around a cleaning brush and
put the end of the rod into you drill...
Forum: Shot Loads For Pistols
I've used split shot sinkers cut in half and loaded into shot capsules. They are great close up. Some decent patterns.
Forum: Lead and Lead Alloys
I use a metal paint stirer and scrape the bottom of the pot before casting. The residue rises to the top and I can scoop it out.
I never let the level get completely down so the residue doesn't get...
Forum: Cast Boolits
I cast sinkers and the best molds I found are the ones with wooden handles over the aluminum. Even with gloves on the aluminum molds get hot very fast.
Nick10Ring
Forum: Lead and Lead Alloys
Can any fellow forum members ID this metal for me? I came into several ingots which are 2 3/4"x2 3/4" and they say the following,"SUPER ALUMALOY BEARING METAL". Is this what is known as babbit or...
Forum: Casting Equipment
I have a heater for my Lyman 450. I haven't started using it yet as I have one more stick of soft lube left. Anyone have experience with this? Bad or good.? Any tips on its use?
...
Forum: Boolit Lube !
I cast with a 6 cavity TL,158gr. 38 mold and I have also used a 148gr.TL,WC mold in the past. I cast the bullets then put a thin coat of Rooster liquid lube on them. I then run them through the Lee...
Forum: Casting Equipment
Guys I need some input and advice. I've been using 6 cavity Lee molds for sometime now. The last session they became very hard to open. They did open but I have a hard time getting the bullets out...
I've been casting for years. When I get frosting I:
1) Turn down heat. Try to finde exact temperature.
2) If you cast for other calibers,try casting with 2 molds during the session.
This...
Forum: Muzzleloading.
It's basically the same as other casting. You do need pure lead, no alloys. I smoke my molds with a candle to get a coating of soot on them. This seems to help the cavities fill out. I cast round...
Forum: Military Rifles
I've used one for years in my Garand. It came from a Garand cleaning kit. It's the ratchet type. You can also get them at Brownell's.
Nick10Ring
Forum: Boolit Lube !
I placed my Lyman 450 in an old grill and heat it on low. Makes it clean as a whistle.
Nick10Ring
Forum: Boolit Lube !
I,ve been casting and reloading for years. I tried some Rooster Jacket and it seems to dry caked up on the bullets unless I dilute it a little. I follow the directions as they came with it. What...
Forum: Casting Equipment
I have a cord from a Lyman furnace. Used once. It will fit both the 10lb. and 20lb. furnace.
$15 shipped to you.
Nick10Ring@aol.com
Struthers,Ohio
Forum: Muzzleloading.
I have a quantity if flints that I won,t need since I have a percussion rifle now. Let me know if you are interested.
Nick10Ring@aol.com
Struthers,Ohio
Forum: In Remembrance
I had 2 Border Collies. We rescued Elroy when he was 6. He was the best dog. He was 15 when he died on Superbowl sunday this year. I still grieve over him. He went with us by his side and his...
I have shot that for years in my S&W .44. I used 10grs. Unique and the Lyman #429421, the 250gr.SWC. It has been the most accurate load I found for the .44.
Nick10Ring
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |