Ive had hit and miss success with the lee molds. I picked up a custom 240gr mold from accurate and had great sucess. You always want to size after pc because you will rarely get a consistent...
Type: Posts; User: bigolsmokebomb
Forum: Cast Boolits
Ive had hit and miss success with the lee molds. I picked up a custom 240gr mold from accurate and had great sucess. You always want to size after pc because you will rarely get a consistent...
Forum: Factory Rifles
ive always put the center of my finger print on the center of the trigger. ive tried just about everything and that's always whats worked for me and everyone ive taught how to shoot. been that way...
Forum: Cast Boolits
I run 147's in my 9mm's for just about all of my range ammo. im a competitive shooter and have the best accuracy and lowest recoil with the 147's. i use 3.2gr of titegroup and have just about one...
Forum: Factory Rifles
the biggest thing when loading for precision is consistency. nothing else matters if the rounds are not consistent. Ive been loading 6.5 creedmoor for 1150yd shooting for a little while and the...
should be a great boolit for 300blk. I recently picked up an accurate mold that has a very similar design to that but in 240gr weight and it was specifically designed for 300blk ar's. ill update...
Forum: Coatings and Alternatives
ive ran PC 9mm for quite a while now and I go through a lot of ammo shooting competition. ive had zero leading issues in my glock with a factory barrel. I just have it sized 2thou bigger than...
Forum: Cast Boolits
good to hear on that load. I just got done building a 16in ar and ive been looking for a good load for supersonic cast boolits. so far all ive been casting for is heavy subsonics but ill be getting...
Forum: Cast Boolits
I know the pain (who am I kidding I love it) I just built a 300blk AR and I reload pretty much everything I shoot. only cast for 2 calibers right now and my lead pile is already getting too small.
Forum: Cast Boolits
im pretty sure I just found your listing for the mold on ebay. I just got into 300blk and im sorely disappointed in the lee mold that I got. i may have to just pick that mold up from you and see...
Forum: Cast Boolits
Needs more heat in the mold. Cast at a faster pace and sort later. If you start to get frosty boolits slow down a step but don't let your mold get cold. I usually cast between 750 and 800...
Forum: Group Buy Archives
Box showed shipped on the 30th (the day after I paid) and I just picked it up from the post office today. Would have been yesterday but my postman is a lazy sob and wouldn't knock on my door. 6...
Forum: Cast Boolits
My gen4 19 eats .358 sized pc cast from a lee .358 150 2r mold all day long. I do have to seat fairly deep but I use titegroup powder and my 3.0gr charge isn't being compressed. I've got about...
Forum: Group Buy Archives
I'm wondering this myself. Group buy's been up for almost 5 months now.
Forum: Reloading Equipment
No issues with it at all. Prime all my pistol on the press and I've probably reloaded 25-30000 rds of 9mm
Forum: Cast Boolits
I would go .357 just to be on the safe side. I mostly run all my cast through a sizer to make them all uniform and I also powder coat my boolits so that adds a few thou to the pre sized boolit. I've...
Forum: Cast Boolits
I see titegroup every time I go to cabelas. Its always on the shelf in quantity.
Forum: Cast Boolits
I've ran my 19 in idpa with great results. I use 147gr pc boolits sized .358 over 3.0gr of titegroup and I can stack 10rds in one jagged hole at 10yds. Poa = poi out of my 19 and my 34.
Forum: Cast Boolits
You need to slug your barrel to see exactly what the diameter is. I can't shoot .356 in my my glock because the barrel slugs at .356. You need to be oversized by at least 2thou over barrel slug...
Forum: Group Buy Archives
Any update on this? I was under the impression when this group buy was posted that it was going to be a quick run.
Forum: Cast Boolits
If you see just a tiny amount of light at only one angle you should be fine. I've got a mold that does that and when it gets hot it goes away. The best way is to just keep at it. It took me...
Forum: Cast Boolits
It could definitely be your mold not closing all the way or possible misalignment. I would clean your mold thoroughly and lube the alignment pins with some beeswax. After cleaning and lubing hold...
Forum: Cast Boolits
For now I've been using the lee 358 150gr rn mold waiting on mihec's group buy to finish up. They shoot well through my glocks and I get no leading with PC boolits. You do need to be careful as you...
Forum: Case Forming / Re-forming
Just converted my first pieces of brass today. I picked up a ruger american predator in 6.5 creedmoor and found out that you can reform 243 win to 6.5. Had a bunch of 243 win laying around from my...
Forum: Case Forming / Re-forming
I have no experience with reloading 762x39 but with my 5.56 I've reloaded it half a dozen times or more without annealing.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |