Search:

Anyone have these in stock yet? I signed up for notification from lee and titan.

Paid .60 a lb this morning. Mixed lead theres usually some solder mixed in the bin I always grab. There were 3 bags of #9 shot i was tempted to grab but passed.

I haven't had much luck with the metallic or sparkling powders by themselves either. They do work well when mixed with a little bit of another powder.

My new lee 312 185 it barely casts at .3105 with cow + 2% tin. As an experiment I added a 1 inch piece of linotype to my little lee pot and got them up to .311 which works for me after 2 coats of...

Went back and used my micrometer and came up with an average of .4734. Recrimped several already loaded rounds and got most of them to go all the way in. Seems like the federal and CBC brass are...

https://ibb.co/gFqNLHL

https://ibb.co/B6CMJ3n

Sized cases measure .472 and chamber fine.

I can give dave a call or stop by, it's only a 20 minute drive for me, I might as well get some head space gauges as well.

I am having an using with a new "match barrel"
Chambers FMJ however my cast loads at .473 only go about half way into the chamber. My factory colt barrel and Springfield plunksnot problem I am...

My results with 2:1 COWW and stick ons +tin are about the same with the noe 135 hp. I get better expansion and less broken noses with the shallow pin. Bullets were shot into snow muzzle velocity was...

Less than my wheel weight + tin boolit. Melted down in my ladle with a propane torch. Melted in down in muffins and will cast a few and check them later.

Melted a piece and after cooling came out to just over 20 bhn

Hello all,
While digging through lead at the scrap yard I came across a large candle holder. It is marked
Coronet plate EP lead. It has slightly more ting than wheel weights. I broke a piece off...

This is pretty much what I do too. Although I do cast a few hundred extra ahead of time its more convenient to powder coat that way. That few hours a week is my me time.

I saw a 1050 mark 7 set up in action last weekend at a commercial loaders shop,it is a sight to behold.Andriod Tablet program runs the whole system, laser sensors, press stops automatically when...

Walnut/corncob tumble
Size and deprime ,look for splits etc.
Handprime with lee primer
Auto Indexing turret press with lee powder through dies and dispenser ,weigh the first 5 charges and every...

I have a colt with a heinie front dovetail would like to have novak cuts becuase of the wider variety of options. Would a simple recut be possible or would it have to be welded and then cut.

$87 shipped for 4 lbs of in stock pistol powder had me looking at etr7. Says to use titegroup data, 4.5-5.5 grains. Any one worked up or ran some through a chrongraph? I've also heard it's csb 1 in a...

Tried out a variation of Ben's LL, 50% Alox 30% JPW and 20 % liquid wax. Dried harder than 50/50. 230 noe hollow point from a 1911 and a 625 average was 863 fps, no leading at all I usually get a...

127605 I love mine 625-4 as well

Very glad to hear that,not that 45 acp is a pressure monster. Might need to break down and buy a chrony.

Single shot 45 acp. Only know that the gentleman I got froms grandfather was a gunsmith. Looks like a blank was turned down and fitted into the shotgun barrel stub. I believe it was a 410 originally...

I size before and after,my lee 452 TC mold drops them at .455 if I size only after PC'ing the coating gets awfully thin.

I took the plunge and decided to give powder coating a try. It was much much easier than I thought it would be. I am very pleased with the results and hope to give them a try this weekend. I would...

I tried fast powders as well and had no luck. I settled on 19 grains of IMR 4895, I suspect something along the lines of varget would work as well.

I've done the same with the lee slug mold lots of cheap fun with my 870.