Greetings
To remove your bullet
Remove the depriming system from your reloading sizer die and resize your ammo to the bottom of your bullet.this will size your bullet down and you should be...
Type: Posts; User: John J
Forum: Reloading Equipment
Greetings
To remove your bullet
Remove the depriming system from your reloading sizer die and resize your ammo to the bottom of your bullet.this will size your bullet down and you should be...
Greetings
The E-clip size is 3.2 x 0.6 mm and the size of the set screw is M4x4 DIN913 (pitch is 0,7mm) copied from M&Ps website
Hope this helps
John J
Greetings
Im trying to find out how long the boolit is from top to bottom
if any one has one of the molds could let me know.
I have sent M&P emails but no reply as of yet
...
Forum: Casting Equipment
Greetings
I have a borrowed mag 20 it is full at the moment so i can only give you the dia of the rod .370 at the top just under the spring.
My wife bought me a mag 25 that is still unused so i...
Forum: Reloading Equipment
Greetings
I found this article on the the bobcat intresting..http://ps-2.kev009.com/ohlandl/310/357-44_Bain_Davis/Guns_Ammo_MAR_1979.pdf
you will have to look into the chambers to see if its...
Forum: Cast Boolits
Greetings
I have that mold and my load is 4.2 ww231 sized .358 and loaded to 1.108 and it works in all my 9mms
John J
Forum: Cast Boolits
Greetings
A few things to try
First i found that the lyman 452460 likes to be loaded to an oal of 1.190 for my BE guns to feed reliable.
The H&G 68 oal is 1.230
The taper/roll crimp...
Forum: Completed Deals
Greetings
depending on how much your willing to pay..look here
www.buffaloarms.com/323-105-grain-round-nose-cast-bullet-mold-for-the-8mm-nambu-1-cavity-jim323105
depending on how much you...
Forum: Casting Equipment
Greetings
I just got a replacement pot for my lee 10#pot that iv been using since the early 70s...because i messed up the original by trying to drill the hole out a little larger..little did i...
Greetings
from an old thread
http://castboolits.gunloads.com/showthread.php?354461-Mihec-thread-question
hope this helps
John J
Forum: Casting Equipment
I think this is what your looking for
https://www.rcbs.com/on/demandware.static/-/Library-Sites-RCBSSharedLibrary/default/dw15e0387c/productPdfFiles/ProMeltElectricLeadFurnaceInstructions.pdf
...
Greetings
I think i found what you were looking for..http://castboolits.gunloads.com/showthread.php?276131-MiHec-DE-CARLI-358-%96-148-Wad-Cutter-Bullet&p=3225758#post3225758
hope this helps
...
Forum: The Star Equipment Corner
Greetings
yes it is pressed in what i did to remove mine was to back the top nut up to the handle then placed in in between the jaws of a vice close the jaws just enough to catch the rim of...
Forum: Completed Deals
Greetings
I would like to buy
1 boxes - 1000 per bx, 10mm, $95.00 per box
1 boxes - 1000 per bx, 38 Super, $85.00 per box
If still avable.
Thank you
Forum: Completed Deals
Greetings
I would like to buy these....308 175 gr HPBT 1 box of 500 shipped for $150
sent a pm
John J
Forum: CB Loads / Military Rifles
Greetings
not sure if this will help but have a look and see if it will for you
https://www.trackofthewolf.com/List/Item.aspx/875/1
John J
Forum: Completed Deals
something for you to read up on
www.dillonprecision.com/450-jr_350_14_386.htm
https://dillonprecision.net/rl450/
but i think a square deal powder die is what you would be looking for.
...
Forum: Casting Equipment
Greetings
To adjust the temp setting you first have to remove the temp dial from its stud...just pull it to you and it should slide off,then look in the middle of the stud you should see a small...
Forum: Reloading Equipment
Greetings
If its a dillon funnel....the short pistol funnels were used with the 450 push/pull machines where the funnel was fixed at the top of the powder die with a set screw.
Hope this helps...
Forum: Cast Boolits
Greetings
Try this next...remove the decaping assembly from your sizeing die and then resize a case.
I think your expander ball is set to high in the die and what is causing your problem.
...
Forum: Reloading Equipment
Greetings
Give Titan reloading a try...Lee makes and undersized sizing die for 38/357
I had to get one for reloading 32auto.
Hope this helps
John J
Forum: Completed Deals
Greetings
I will adopt your mold and give it a very nice home.
PM sent
Thank you
John J
Forum: Group Buy Archives
Got mine today-- RH008086563SI 2359 Pembroke, MA US
Thank you MiHec
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |