I have just picked up a 38-55 1894 Win today that exhibits the same problem ie the last bit is awkward, but I only found out about 15 minutes ago that there are 2 lengths of cases.
The one I got...
Type: Posts; User: JakeOz
Forum: The Star Equipment Corner
I have just picked up a 38-55 1894 Win today that exhibits the same problem ie the last bit is awkward, but I only found out about 15 minutes ago that there are 2 lengths of cases.
The one I got...
Forum: The Star Equipment Corner
Below is a message I sent to the company mentioned above about a concern I have with 38-55 Winchesters. This problem may become even more personal as I am about to purchase (possibly an...
Forum: Cast Boolits
Harpman, please get a casting thermometer and check your temperature. You are getting dangerously close (if not already at it) for lead to start to vapourise. This is a dangerous place to be. I cast...
Forum: Cast Boolits
Not easily and too darned expensive, let alone the environmental issues concerned. There are also some serious health issues to be considered as the processes give of some very dangerous by-products....
Forum: The Star Equipment Corner
Just thought I would let everyone know how this thing is progressing.
Have lubed and sized approx 2000 44/40's and no more probs.
Have done about 7500 44 Mags as well as 32.20's, 38/40's and...
Forum: Casting Equipment
Why not use a muffin pan. They have 12 nice little round pots and hold approx 2 lb each. Fill all 12, load up the pot again, by the time that has all melted and been cleaned up, tip the cakes out and...
Forum: The Star Equipment Corner
My business partner and I just got back from a range about 2 hours from here.
We collected a little bit of range lead and will need to go back for another 4 trips to collect more.
This trip...
Forum: The Star Equipment Corner
I have just done another 3500 .38's (this time 158g SWC PB) and had no real dramas. Did not need to remove and clean the die at all. Will finish off the remainder tomorrow and do another round of 158...
Forum: The Star Equipment Corner
3six,
pardon my ignorance, but what is All. We most likely have it downunder, but under a different name.
Would it be a Silicon spray, a water dispersant like WD40 or CRC etc ?.
Regards
Forum: The Star Equipment Corner
Set everything up for 38's in 158 grn RNFP and it is working like a charm.
The 44's finished OK (only about 600-700 needed doing) and it did OK. Will need to check to see if any hole have filled...
Forum: The Star Equipment Corner
KY, I was thinking along similar lines, but the holes are so darn tiny. A #59 drill bit is vewy, vewy small.
I would need more than just glasses to see 'em :roll:
Thanks for confirming...
Forum: The Star Equipment Corner
It would appear that there were some burrs. Got to it with some 800 grit wet & dry paper and did a little clean up and it ran for a little while before clogging up again.
Got annoyed with that and...
Forum: The Star Equipment Corner
SixBits, they are approx .430 if not .429.
RM, yes to being used. The very same die I am experiencing the problems with has been used before and ALL the holes were cleaned out then and the...
Forum: The Star Equipment Corner
I have recently obtained one of these devices and am having some issues with it.
I have been trying to size some projectiles to .429" and while I have been getting the adjustments ok and running...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |