Search:

Payment made via. PayPal ~ Past Tense !!!

[smilie=w: :drinks:

Correct for me !!!


------------------------------------------------


What I find most interesting is the pattern of several popular sizes that developed. Although I do not believe this...

With the length of the blocks he is using on this run (as far as I know):

Max number of cavities he can do in 0.495 size is 4 cav.
Max number of cavities he can do in 0.575 size is 3 cav.

...

LOL !!! :smile:

Actually, I just measured the actual size (as in the actual diameter of the balls they cast with pure-ish lead) of my existing single cavity molds that I already have loads...

The active group buy on this is only going to be open so long, if you want in on this wonderful opportunity then NOW is the time:



...

Decision made, I will take:

2 @ 5-cavity 0.411" RB
2 @ 3-cavity 0.679" RB
1 @ 3-cavity 0.626" RB

So that’s a total of five molds for me, Thank You !!!

...

There have been discussions for over a year on doing a group buy for multi-cavity round ball molds where everyone will get to pick their own custom size ball that they want/need for their...

There have been discussions for over a year on doing a group buy for multi-cavity round ball molds where everyone will get to pick their own custom size ball that they want/need for their...

There have been discussions for over a year on doing a group buy for multi-cavity round ball molds where everyone will get to pick their own custom size ball that they want/need for their...

At current I'm trying to decide how many molds to get on this one which I clearly indicated in the proposition thread that I was going to be in on. If I only buy three or so that leaves some of the...

As to the "welcome to my world" as to fighting the snow. Yah, I've said something very close to that more then once when watching TV news and seeing all the yo-yos in the south east freaking out...

I plan to get some more load development and test shooting in with them but right now I'm pretty much snowed under and its all I can do to just keep up with my chores and responsibilities and keep my...

I am extremely saddened by some of the posts in this thread. There is at least one member who has posted in this thread that based on action in this thread I have put name on my very short list of...

My woman has a 50-BMG gun that is a take down gun that comes apart in three pieces, barrel, center receiver/scope group, and stock that fits in its own special small suitcase.

That thing is a...

I have shot gas checked boolits from my CZ-52 but ultimatly found it unnecessary and found plenty of loads and boolits that shoot just fine plain base from that cartridge/gun with no leading and...

I just loosen up the sprue plate and/or as Bullshop suggested just smooth off the top inside corners of the block faces to get good base venting.

Closest thing currently on the market (not old stock) is the 1/2" thick waxed cards that BPI sells for $ more then normal nitro cards in a few but not all guage sizes. I have never had the chance to...

Not sure if we are going to get enough takers on this buy for it to actually go through. But if it does, Don't bother with putting the wood ball handles on any of my pins. Just leave them with the...

Oh, yah, forgot to mention. With soft nearly pure lead with no tin added my slugs came out at 0.732" diameter or so. Hard WW alloy slugs were 0.735" or so.

Okay, found the battery charger for my old 5-mp dig camera that although not nearly as nice or good as my good dig camera is way better then the trash camera on my cell phone. Re-took some photos of...

Yup, that's the theory. I have recovered bullets fired into snow drifts (specifically for recovery in as close as possible to muzzle exit condition) and this has lead me to believe there is a little...

@ 338RemUltraMag

Okay, I couldn't get a magnet to stick to the pins and they didn't heat blue and their electric conductivity seemed too high for stainless but was still slightly lower then the...

Oh good grief !!!

Must there always be such arguments about such crazy stuff. I've deliberately tested two guns with chokes to failure years ago by firing harder and hard alloy full bore slugs...

Long story short, as it sits right now I'm satisfied with the mold. I wouldn't consider it a mass production mold (not as in who how it was made but rather as in a mold capable of producing massive...