Good job, low power loads in 30-06 is always fun!
CC
Type: Posts; User: clearcut
Good job, low power loads in 30-06 is always fun!
CC
Forum: CB Loads / Military Rifles
for a 16" barrel carbine gas system should be fine for function.
CC
Forum: CB Loads / Military Rifles
I think it looks great I do the rattle can on all kinds of guns and hunting gear they come out looking fine and a little wear n tear looks cool.
CC
Forum: Coatings and Alternatives
Some times I'll warm up the bullets to around 100*-110* when it's cold, Smokes powder is the easiest to use, rolling the bullets around with your fingers and nitrile gloves on helps to even out the...
I use 35 grn. of IMR 4895 with a lee 150 grn. PC'd Gc. rnfp around 2400 fps. dropped a black tail like a rock.
CC
Forum: Coatings and Alternatives
I just lubed my last batch of PC'd boolits what a difference ,smooth as Tennessee whisky, I just hit them with a light spray of Dillon case lube . They were a little stiff going through the die @...
Forum: CB Loads / Military Rifles
Outer Rondacker
In the 223 I use the NOE 225 62Gr. FN with the gas check and PC it comes out to 67 to 68 Gr.( my alloy WW, dental lead, solder, etc.)sized to .224 after PC. note : my wylde don't...
Forum: CB Loads / Military Rifles
Robert12345 I have one of those it's called a 300 blackout I use cast in it all the time .I also use cast PC'd gas checked in 1:7 .223 no problems.
CC
Forum: Coatings and Alternatives
smoke's dependable and fast turnaround I love the Carolina blue !
CC
Forum: CB Loads / Military Rifles
I like the Lee TL309-230-5R 1090 fps with my load.
CC
Forum: Coatings and Alternatives
Smoke is a strait shooter :2gunsfiring_v1:
CC
Forum: CB Loads / Military Rifles
I'll bore it out it's just for Cali laws, flash suppressor is too scary in this state.
CC
Forum: CB Loads / Military Rifles
Looks like there is some lead and Carolina blue on the 1st port on the right hand side.
CC
Forum: CB Loads / Military Rifles
Thanks Larry but it shot great with the flash suppressor. I'll probably switch it back so I can use up lots of ammo I've loaded for this ar.
CC
Forum: CB Loads / Military Rifles
I added compensators to my ar15's and the grouping went out window . I know the harmonics have changed but from 1" to 8" at 40 yds is radical.
16' bbl. 1:7 twist
62 grn. powder coated gas...
Forum: CB Loads / Military Rifles
It can be done both ways I PC then check , I push them around 2.400 fps.
CC
Forum: CB Loads / Military Rifles
I went with the NOE 62grn for my 1:7 twist it works well on top of some(21grn) IMR 4895 .
CC
Forum: Factory & Surplus Powder
5.5 grn. in a 30-30 with a cast 150 grn. is fun to plink with
CC
Forum: CB Loads / Military Rifles
Why can't you run them fast? 4.5gr. Trailboss should get them out of the barrel 6.3 is the max TB load @1046 fps.
CC
You need to go heavy to get the AR to cycle at low speeds. You may want to start at the suggested 6 grns of pistols powder and change it up or down to get the speed you want ,remember a squib without...
I'm having good luck with 35 grn. of IMR 4895 under a Lee 150 rnfp PC'd and gas checked. It's a bolt gun so no function issues. Getting 2" @ 100 Yds with the random flyer once in a while.
CC
Forum: Coatings and Alternatives
Shake n bake w/non stick foil, used toaster oven, thermometer, smoke's sample pack.Under $30.00 you can't go wrong for cheap PC. Just like reloading you'll save tons of money:2gunsfiring_v1:
CC
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |