That blog entry says in Japanese as follows;
no official announcement on Lyman web page
no information found but handloader ads
8 years pass since 49th published
must buy one even only the...
Type: Posts; User: tomo
Forum: Reloading Equipment
That blog entry says in Japanese as follows;
no official announcement on Lyman web page
no information found but handloader ads
8 years pass since 49th published
must buy one even only the...
I found a shop sold the 5th edition in Japan. It costs about $40 including S&H.
Most reasonable method to get it is buying the book with other item and shipping in one parcel.
But I won't have a...
Thank you, Dan.
I have 4th edition and should order new one since longshot is on. But I found it in Amazon and its s&h costs $46!!! (to Japan in 1 week)
I will PM.
Are there any recipe if 12GA Lyman 525 gr sabot slug + Longshot?
I have a Lyman foster slug mould. According to my old book, load data with SR4756 and other powder are available but I can not find one with Longshot.
Can you show me the load data? Polyform...
Forum: Gas Checks
Thanks for ideas. I have tried to use WD40 but it didn't work.
I could not get perfect so far but dry lube (graphite powder for neck sizing) works 80%.
And rotating under die to change relative...
Forum: Gas Checks
If 0.4mm(0.016") is too thick, I can buy 0.3mm (0.012") copper or/and aluminum at a local hardware shop.
But when I use copper with 0.3mm thick, it was hard to cut disk from a strip.
It will be...
Forum: Gas Checks
Hello Pat,
I am using 30cal. The check which sticks on male die, are made of aluminum and its thickness is 0.4mm (0.016"). It might be too thick to form?
I can buy other thickness metal, thinner...
Forum: Gas Checks
I didn't take care of down side part. I will do clean them.
Thank you, FrontSite.
Forum: Cast Boolits
At first, thank you for additional great information.
I carefully inspected every case soon after each shot. And there were not any pressure signs on primers and cases when they were shot.
I...
Forum: Cast Boolits
I made 30-06 reduced loads with Hodgdon Longshot finally.
According to great advice from Blackwater (comment #2), I loaded 15 to 17 grain Longshot and 170 grain cast boolits.
I forget to bring my...
Forum: Gas Checks
Thank you, Dan.
I did only wipe dust off and didn't use any sand paper. I will try them at next batch.
Forum: Cast Boolits
Hello fredj338,
If I can have only one mould for 308, should I choose 311 instead of 309 and have several size of sizing dies?
Forum: Cast Boolits
I am a newbie and have .309 for 30cal too.
A good guy in this forum taught me that the size should be increased a little bit if you find inaccuracy.
I think .309 is nice for first try.
Forum: Gas Checks
Hello folks,
I started to make gas checks with checkmaker from Pat Marlins.
I bought a piece of copper and aluminum sheet with thickness of 0.3mm(0.012") and 0.4mm(0.016") respectively.
It needs...
Forum: Cast Boolits
jmsj,
I will use cast bullets for 30-06 reduced load at first.
I asked Pat to send his checkmaker and it is on the way,
and it will arrive in this week. I will have a chance to shoot
cast...
Forum: Cast Boolits
44man,
Thanks for showing a picture which I have never seen.
Of course, I didn’t know the front check before your post.
Now a day, OBON becomes just summer holiday for the most part of us....
Forum: Cast Boolits
Hello folks,
I am returning from my parents house for OBON holiday which is a time when the Japanese traditionally welcome our ancestors' on Aug 13th and send them back on the 16th.
Anyway, thank...
Forum: Cast Boolits
Thanks Tom and lobowolf761
Actually I have only .309 sizing die for 308. Anyhow I will try with bullets I made yesterday at first.
Forum: Cast Boolits
Thank you Tom,
BHN of bullets I casted yesterday was about 15 according to pencil tests.
But I am not sure that how fit they are.
I am going to use a .309 dia sizing die. Do you think I should...
Forum: Hunting with CB's
Thanks for great offering and your kindness, Whiterabbit.
But I have only .308 rifles not 7mm so far. I have been SF for sightseeing 20 years ago but I had no chance to visit there after that, even...
Forum: Cast Boolits
I'm going to shoot cast bullets of 30-06 at about 2000 fps.
How much BHN is needed if bullet has gas check?
Is there a guide table or chart of correlation between BHN and muzzle velocity?
Forum: Lead and Lead Alloys
I bought Staedtler pencils, H, F, HB, B and 2B. They covers BHN 11 to 22.
It is difficult to get flat ends of cylindrical lead. So I use a sharpener with setting to NOT keenly.
It needs flat lead...
Forum: Hunting with CB's
According to a US regulation, shotgun hulls can be exported from the states without any license. But it needs export license to ship rifle-related bullets and cases. They are US side matter. On the...
Forum: Hunting with CB's
Yes! I dreamed that I can use a lathe to make bullets. Before I buy a lathe, I must make more space for it.
Using lathe must be fun that making a lot of designs and talking about it at this forum.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |