Reloading EverythingRepackboxRotoMetals2Titan Reloading
Inline FabricationWidenersLee PrecisionMidSouth Shooters Supply
Load Data

Search:

Type: Posts; User: waksupi

Page 1 of 99 1 2 3 4
Results 1 to 25 of 2467

Search: Search took 0.12 seconds; generated 9 minute(s) ago.

  1. Replies
    16
    Views
    554

    I believe the original post answered that...

    I believe the original post answered that question. As does your own post.
  2. Replies
    22
    Views
    824

    Forum: Our Town

    At our military and sporting rifle matches, heavy...

    At our military and sporting rifle matches, heavy angle iron is put over the hangers. Saves them pretty well.
  3. Replies
    23
    Views
    705

    Forum: Our Town

    I worked in an industrial radiator factory in the...

    I worked in an industrial radiator factory in the early '70's. Aluminum was the rule of the day for the big heavy equipment radiators. Some weighed over 400#, so weight was an issue.
  4. Replies
    16
    Views
    554

    They make a lovely companion piece for their...

    They make a lovely companion piece for their Taurus.
  5. Thread: lemat loads

    by waksupi
    Replies
    12
    Views
    489

    This board is famous for hijacking! Now, what was...

    This board is famous for hijacking! Now, what was it you wanted to know about mouse traps?

    As long as we keep the thread alive, a Lemat owner might find it!
  6. Replies
    11
    Views
    583

    Forum: Our Town

    It used to be a downright busy place.

    It used to be a downright busy place.
  7. Replies
    19
    Views
    984

    Forum: Our Town

    Many of those will interchange with other rifles...

    Many of those will interchange with other rifles if you are just looking to strip some rounds in while plinking.
  8. Replies
    23
    Views
    883

    Forum: Our Town

    Two mills shut down here in Montana this week,...

    Two mills shut down here in Montana this week, wood is going to go up!
  9. Replies
    9
    Views
    536

    I've done that in the past. After that lesson,...

    I've done that in the past. After that lesson, punches got chucked up in the drill press, and polished to remove all machining evidence, and remove a couple thousandths of material.
  10. Thread: "hard cast"

    by waksupi
    Replies
    21
    Views
    726

    Forum: Cast Boolits

    I'm with you. To me that indicates their only...

    I'm with you. To me that indicates their only experience is with commercial cast bullets.
  11. Replies
    19
    Views
    701

    Forum: Cast Boolits

    Don't get into a rush sizing those. Drop one in a...

    Don't get into a rush sizing those. Drop one in a cylinder, and see how tight it is. You want them to fit the cylinder so you can push them through with a little pressure with a pencil. I suspect you...
  12. Replies
    101
    Views
    2,782

    Forum: Cast Boolits

    No need for the flux. Stir your melt with a dry...

    No need for the flux. Stir your melt with a dry stick, and save your money.
  13. Replies
    14
    Views
    442

    Forum: Cast Boolits

    Rifle or hand gun? Rifles are more forgiving, in...

    Rifle or hand gun? Rifles are more forgiving, in my experience.
  14. Thread: lemat loads

    by waksupi
    Replies
    12
    Views
    489

    I would stick with round balls to ease the...

    I would stick with round balls to ease the learning curve. Check Osbourne punch measurements, find one the right size and punch out your own wads.
  15. Thread: tent trailer

    by waksupi
    Replies
    15
    Views
    520

    Forum: Our Town

    Too many wear points on a tent trailer. I would...

    Too many wear points on a tent trailer. I would personally pass. Another consideration, in bear country, they are the equivalent of a soft shell taco.
  16. Replies
    18
    Views
    636

    Good lines!

    Good lines!
  17. Replies
    7
    Views
    278

    It shouldn't make a difference, but the metal...

    It shouldn't make a difference, but the metal should actually be sand blasted before spraying, rendering the question moot.
  18. Forum: Cast Boolits

    Zinc wheel weights have been around for at least...

    Zinc wheel weights have been around for at least 50 years. At least, that's when I first ruined a pot of alloy because of it.
  19. Replies
    49
    Views
    1,333

    Forum: Our Town

    Needs course ground pepper and ginger!

    Needs course ground pepper and ginger!
  20. If you think the hammer fall is slow, look for...

    If you think the hammer fall is slow, look for wood to metal contact inside the lock mortise.
  21. Replies
    22
    Views
    906

    Forum: Cast Boolits

    Save the bullets, scrap the rest. There could...

    Save the bullets, scrap the rest. There could well be serious copper precipitation inside you can't see.
  22. Replies
    14
    Views
    547

    Is it loose when the barrel is hot?

    Is it loose when the barrel is hot?
  23. Replies
    26
    Views
    960

    Forum: Our Town

    I hate to think of what kind of a person I may...

    I hate to think of what kind of a person I may have become, had dad not started me in fishing, trapping, and hunting as soon as I was big enough to tag along. Keep on being that "bad influence"!
  24. Replies
    21
    Views
    537

    Forum: Our Town

    In Montana, we always get six months of winter....

    In Montana, we always get six months of winter. You just never know which six months it will be. I've seen it snow every month of the year here.
  25. Thread: Moose Milk

    by waksupi
    Replies
    8
    Views
    770

    I've used them dry to load for hunting. For cold...

    I've used them dry to load for hunting. For cold weather, try windshield washer fluid rather than water.
Results 1 to 25 of 2467
Page 1 of 99 1 2 3 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check