reclaim shot . would be hard to tell as it is a mix from many years of different brands .
Type: Posts; User: shotman
Forum: Lead and Lead Alloys
reclaim shot . would be hard to tell as it is a mix from many years of different brands .
yes and work good but need to change handles to this
Forum: Rimfire Area
I think winchester dropped the "wildcat" or redesigned it but they would jamb all the time .Never had problem with rem reg win or fed. Dont use the hot cci's
Check CDNN they did have mags last...
If you load hot just do a few. there is reason for the high brass.
guy on trapshooters has the high brass hulls from time to time
About all plastic has a lifetime built in, Its so it dont last like glass in a land fill. wads will keep 20 years in the dark and below about 80* but in the bags that can get light about 1/2 that....
Forum: Reloading Equipment
bb is right BUT if the insides have been changed you are on your own
Its a hit and miss. When you get them figured out get a silver sharpy and wright on them
Forum: Our Town
well redwings are made in --you guessed it. the thorogood is made in WI. Have 2 pair and like both
yes but your mix is very hard to control. I have tried everything out there. Oil works the best as it dont get thick or thin. If you keep temps at about 110 * max.
the pop corn is from too thin...
Forum: Gunsmithing Tips & Tricks
It will make a mess out of AL. I had some that was 10% and it cleanded very good . so Took a lawnmower piston that had lot of carbon bulid up. put in coffee can. 2 days later had the rings and...
Forum: Factory Rifles
dont matter what you use. SHOT placement does
Forum: Factory Rifles
would bet rem as a copy cat used the 243win. to come up with the 22-250 250-3000 is about same
anything rem made was a copy of someones design. but they made it cheaper
Forum: Factory Rifles
guessing you are talking about center stock screw??? keep it tight,. that is a second recoil lug
Most wins dont like cast unless you size to .277. which is special
no they hang tight same as the turkey loads in the mags
Well, no 1 a 28ga for trap is a hit and miss [pun intended} your best bet is a duplex load of 7 1/2 and 8 or 9 . That way you have a load as dense as possible. The 20/28 powder is good. Need to...
most were used in the fiber base hull. what hull are you loading ? or wanting to load ?
Forum: Our Town
they have a clothes dry thing at the dollar stores it will sit up on its side if you side the rails in makes a pocket . about $6 and is about 30x30 in
Forum: Cast Boolits
Well if you know an electrician the contact points are silver in the larger breakers.
you need to use a STEEL mold and I used the cast pour ladle to heat the silver. the mold needs to be dull red....
Forum: Reloading Equipment
guess you dont have a Heavy Duty deprimer.
Panty hose works better and if used they smell good
Forum: Gunsmithing Tips & Tricks
need to heat it. most are silver solder. put wet rag about 1/2in back and propane torch. but when it pulls do a fast wipe with a dry rag. and let cool , not with the wet rag
Take all the guts...
Forum: Reloading Equipment
glass is easy to cut. single and dont over tighten
Forum: Factory Rifles
54 and 70 are same . remember that is a control feed. out of mag only
Good luck in your project. First water dont work and .020 is way to big . That is why the shot makers sell for $350
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |