I have had the same experience. But I run the tightest drop tubes, adapters and springs the bullet will go through comfortably.
What I found was the first coil of the spring would push into the...
Type: Posts; User: Gillie Dog
Forum: 3D PRINTED RELATED ITEMS
I have had the same experience. But I run the tightest drop tubes, adapters and springs the bullet will go through comfortably.
What I found was the first coil of the spring would push into the...
Forum: Reloading Equipment
LEE sent me the orientation lock for all Auto Drum measures I have, when I requested them, just for the reason shown in the video when I tested/installed an Update Kit. In 2017 they started adding...
Forum: 3D PRINTED RELATED ITEMS
Excellent you are on your way.
GD
Forum: 3D PRINTED RELATED ITEMS
I forgot to add that I would recommend the hex coupler box be checked also for using the clutch in collator plates. With those selections and hex coupler about all I see missing is prox sensor...
Forum: 3D PRINTED RELATED ITEMS
No it does not make any changes in the main body (or anything else) based on selections, it just puts it in the parts needed for the project. Project generator just makes parts list and assembles...
Forum: 3D PRINTED RELATED ITEMS
This is what I use for all 9mm from my set up sheet. I did polish the insides of the #9 spring adapters and drop tube with fine sandpaper though for use with 38 SPL also.
GD
Collator...
Forum: 3D PRINTED RELATED ITEMS
No problem at all, I printed a 300mm before getting to that one. Let us know how it prints if you do one.
GD
Forum: 3D PRINTED RELATED ITEMS
TinkerCad has same problem. No snap to dimension or line or extension, no align to other object, etc., like we had in AutoCad.
GD
Forum: 3D PRINTED RELATED ITEMS
Here is TylerRs on the collator. I never printed it because I have 300mm for cases.
It is probably 3 or 4mm shorter than attaching with the "clamps"
321096
Forum: 3D PRINTED RELATED ITEMS
I hope I am understanding correctly, and you are using #12 spring adapters and 12mm ID spring for a 38/9mm bullet, I believe you are using too large of spring adapters and spring. For that diameter...
Forum: 3D PRINTED RELATED ITEMS
Yea, you know how it goes. Solder/shrink tube connections, ferrules on stranded wires in terminals, cable ties, wire routing to prevent rats nests, etc......... My OCD won't let me use wire nuts on...
Forum: 3D PRINTED RELATED ITEMS
I use the JST 3 wire connector for the prox sensor but I customized my electrical box without all the holes, just one with a grommet and strain relief.
I solder and shrink tube the wires to the...
Forum: 3D PRINTED RELATED ITEMS
With a little massaging of the first coil the DAA output chute springs works quite well with #12 and #13 adapters but is to small OD for the #14 adapters. Also the 44 mag case does not like the DAA...
Forum: 3D PRINTED RELATED ITEMS
Thanks,
18mm OD spring for #14 spring adapters?
Thanks
GD
Forum: 3D PRINTED RELATED ITEMS
Thank you,
With that memory nudge, I now remember reading about those/that supplier somewhere in this thread.
Thanks
GD
Forum: 3D PRINTED RELATED ITEMS
Yes that is the one I am looking at.
Spring I have works fine with #13 but 44 will not go through it so looking at larger.
Thanks
GD
Forum: 3D PRINTED RELATED ITEMS
Thank you,
I will check the size with them but I assume it must be in the 5/8 range. I am using smaller spring for 45 ACP with smaller adapters but will not fit the 44 mag.
Thanks
GD
Forum: 3D PRINTED RELATED ITEMS
Hello Group,
Can anyone make a spring recommendation for use with the #14 spring adapter and spring adapter DT? This is the last part I need to complete case feeding the six pistol calibers I do,...
Forum: 3D PRINTED RELATED ITEMS
Yea, in our system pipe size refers to inside diameter so 1" pipe has a ~1.3" outside diameter (~33mm) and 3/4" pipe is ~1.05" outside diameter (~26.7mm).
We strive to make things difficult you...
Forum: 3D PRINTED RELATED ITEMS
It measures 28mm in the stl file so what you are getting looks about right. The pole I use is about 26.8MM (3/4" pipe) and seems to work fine with clamp screw just finger tight.
GD
Forum: 3D PRINTED RELATED ITEMS
Understood, printing one now even though I run not that steep on bullet collator, it will come close to making spring vertical.
Many thanks, I very much appreciate and am amazed at all you have...
Forum: 3D PRINTED RELATED ITEMS
Thank you,
I have never looked at a nose down bullet slide plate to catch that.
GD
Forum: 3D PRINTED RELATED ITEMS
TylerR,
I am trying to determine the difference between the Drop Hole Adapter; Angled, Angled Slide and Angled Body.
Looks like angled and angled slide are same with mounting holes such that...
Forum: 3D PRINTED RELATED ITEMS
For pistol, I have found it depends on the case, some need more tilt, positive from vertical of brass hole adapter, and some will run with less tilt than vertical. Once determined how much tilt of...
Forum: 3D PRINTED RELATED ITEMS
I agree and I filled in the bump before the drop hole as not needed for pistol brass also.
GD
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |