Search:

I have converted almost all of my lubrication needs to coconut oil. I have the big Costco tub in the kitchen so it costs me virtually nothing. I keep a 2x2 patch loaded with it and just occasionally...

Come on now The seating die method assumes several things.
All cases are trimmed to a single length.
Cases are soft enough to be roll formed .
Shoulder angle is flat enough to not buckle the...

Nothing wrong with a good single shot. This is what I did with one.
107337
107338
107339
It is my adventure gun. It has a good supply of things you need when you find yourself somewhere stupid....

As long as your Craigslisting put the cookie oven on you search list. I bought mine for $30. It will hold three cookie sheets full and has a nice circulation system.
101292
101293
I adjusted the...

Being from Seattle land of moss I will be sprinkling them liberally on my roof. The copper should leach out of the brass and be fairly good moss control. They should turn black and just about...

Sounds like you cooked the SSR. If it came on and was working for a while it is probably wired right. You just need to keep the SSR cooler

Everything else being roughly equal slicker is slower. The HBN and Molly guys have dealt with this for years. Modern powder needs pressure to make pressure and PC'ed boolits are just outrunning the...

I don't know the specifics of your machine but there are a few possibilities
1 Just a brass muffler to keep the noise down.
2 A variable restriction to slow down the speed of the piston. It is...

http://seattle.craigslist.org/see/zip/4289582125.html
If your in Seattle this would be a great PC oven.
Not mine just saw the add.

I purchased a pound of the teflon black and a pound of the anti graffiti clear. I have only done a simple melt test on a sheet of tin foil. Both were a high gloss and fairly slippery. The black may...

If it won't come out and you shoot flat black I have to ask have you slugged the barrel to see if you have any rifling left?
Just drop a round in and start tapping it through from the breach end. If...

Does anybody have any data on how fast you can push a PC rifle bullet without a gas check and how much faster will it go with a gas check? My thinking is that a LEE tumble lube design with...

Silver Shooter
From what I understand
Yes he has a high twist rate barrel and he is PCing in flat black.
The flat black has either eroded the rifling away for several inches of his bore or the...

If you don't have a tube of Autosol in your arsenal buy a tube....

He has the ground clamp on you can see it in the picture.
The foot pedal now that is a different question.
92809

Maxbob I suspect that your high voltage isn't working very well.
I used my dads gun and it made a mess like you have there. I bought my own and it worked drastically better.
Same techniques you...

Here is my HF list
92688
Definitely skip the 1/4" yellow coiled hose 20' try 4' unless you tie it to a truck.
I splurged for the the upgraded regulator
It takes very little air to run the gun...

425 will definitely turn them brown. It doesn't seem to effect the adhesion or flaking but it probably effects the hardness and probably the lubricity.

I made it down the learning curve a long ways this week.
The oven is a pain to get dialed in to 400 deg. but with a lot of patience it is there. Digital next time.
My dads brand new HF powder...

Here is a nice map to check your state for teflon restrictions.
http://www.shotgunworld.com/bbs/viewtopic.php?t=99006
The only state that looks like it has a ban on Teflon polymer blends is...

I was digging around the net this morning and found these guys. All Powder Paints.
They have two products that I was interested in. The anti graphiti clear and the Teflon Black....

I found the oven on Craigslist for $30 the tray was $3 at big lots It doesn't have an external temp set, you have to pop the cover to adjust it. I may add a nice digital control.
I read the thread...

I went to Harbor Freight and bought some red and black powder coat.
Today I played with a few micro experiments on my hot plate.
Tonight I picked up a Convection cookie oven.
91544
91545
91546...

If you want to put the hole in the center of the boolit every time you spin the boolit and fix the bit. It draws it to the center.
Hold the boolit in some form of a Collette chucked into a small...

Hi guys
Thanks for the interesting research.
From my knot hole I can see a distinct advantage to hard coat vs lube.
I have a LnL progressive set up for 9mm that I batch several thousand rounds...