Search:

One of these

https://m.media-amazon.com/images/I/71N5bAedAVL._AC_SX679_PIbundle-3,TopRight,0,0_SH20_.jpg

I have had the same experience with this nose rider design. Fine tuning the nose diameter with NOE push trough nose sizing dies cleared the issue for me. I wasn’t excited about purchasing more tools...

Sounds like you’re set on everything else but powder. If so, I’d look up what your manuals have for that weight that appears most on two fronts: the manual and the shelf, and then order some. Powder...

If it were me, I’d keep the different lead separate. You can melt and remelt to get fluxing experience, but I’d just cast from the ingots you already have to get started. Once you see the first cast,...

I vote bubba rountree on YouTube. I don’t know of a one stop shop, but there is some overlap of payload weight it seems. I have the bpi buckshot manual and like it for the components I have on hand....

The command series of Kohler engines are tough. I’m in the Lawn business and have a couple with well over a thousand hours on them. The horizontal twin opposing cylinder Briggs engines might be...

Look at the ender 3 or the ender 3 pro. Creality is the “brand”. I’m not all that tech savvy and figured out how to use a program called cura. YouTube has info on both. The printer is less than $200...

I’m going against the grain and suggesting your crimp is fine. The pill is too fat for the lands/rifling at that particular seating depth. Dummy up a round and seat it deeper. I don’t know if all the...

I like it! I recently got a Keter workbench for reloading in the RV and this gives me some ideas. Looks like a predecessor to the inline fab type reloading bench accessories. Love the pic, and great...

Sell them now. Prices are up, keep all you want, but sell is my advice.

My sisters (ex) husband passed away and left stuff for my sisters kids to deal with. My sister ended up having to handle the...

Britts donuts in Carolina Beach NC!! It’s not just the donuts, I think the near ice cold milk they serve with them makes for an experience. It’s tucked in the old board walk. Absolutely delicious!

Nice lever action , check in over at the Rossi forum. Great wealth of info.

https://www.rossi-rifleman.com/index.php

Mark

Looks good. I might have to try this on my Lee 300 BO die. It cuts the nose on the c312-155 . Puts a perfect circle on the nose.

Good job.

Mark

To isolate the problem to the carburetor, slowly slide the choke toward the choke position. (While it idles) If it cleans up and stops surging it points to a dirty carb. My money is on the carb, we...

I have had no heat in my 98 f150 and was sure it was the heater core. Well, it sort of was, but the main issue I had was the water pump. I had an issue with corrosion in the coolant but did not know...

38 S&W expander is the one you need. Not 38/.357. Try it, you’ll like it.

Yep. It adds another layer to the fun.


Um, could we have a pic!

Nice! They are almost as much fun to build as they are fun to cast with.

Enjoy!

Have you checked the oil level? Low engine oil in the 7.3 can cause these symptoms. The hpop starves when under higher rpm and cannot tell the injectors what to do.

Mark

I’m sure you don’t want to hear this, but the 38 special expander is not what you want.

Call lee again, and get the .38 Smith and Wesson expander stem.

You may or may not be able to keep from...

Pull a bullet.

Doug Guy and John McCorkle are on to it. I’d echo exactly what they say with the addition of using the Lee powder through expander in 38 S&W. It expands a little deeper and fatter.

Hold off on...

Lloyd, that particular mold is on clearance at midway. Awful tempting, and free shipping to boot!
...

I’m betting that boolit is getting sized down somewhere. Push an unsized boolit through the cylinder and see if it’s under .431 when it gets to the forcing cone. Not sure if that’s your issue but I’d...

They would be sent down the pipe if they were mine. I have no troubles with PC, don’t see why hi tec would be any different. If accuracy goes south see if the bore has lead. As long as they are at...