That's exactly the kind of info I was looking for :-D. We'll see how it goes, maybe I can post some before and after results.
Type: Posts; User: MeestaSparkle
Forum: Cast Boolits
That's exactly the kind of info I was looking for :-D. We'll see how it goes, maybe I can post some before and after results.
Forum: Cast Boolits
I forgot to mention the pot fullness.. but that was another variable I tested for. I tried everything from 25% full to near 90%.
As far as spout clean-ness goes. I got that paper clip trick on...
Forum: Cast Boolits
I built a PID temperature controller and have a thermocouple near the spout on the bottom.. so temperature should not be an issue... I set the temp digitally and it holds it to within 10 degrees or...
Forum: Cast Boolits
Hey,
I am pretty new to casting and have been unable to get satisfactory results with my lee pro 4-20 pot. I have spent many hours casting at different temperatures from very low to way too...
Forum: CB Loads / Military Rifles
Got to take my garand out for the first time, and since I've been having trouble with my 314299 I just loaded some 147 winchester FMJBT. I was surprised, I think this rifle has the potential to be...
Forum: Cast Boolits
Thanks for the replies everyone :) I have a question about fluxing. WHen I drop paraffin on the top it melts and then appears to pretty much just burn off before I can mix it in. How should I be...
Forum: Cast Boolits
I posted a while ago about having trouble with my 314299. Well, I did some of your suggestions, and here is the result. I casted about double this, but had a 50% reject rate. It looks like there...
Forum: Cast Boolits
Thanks for the replies, guys. I am going to take a carbide scribe and run it along all the vent lines, and see if that helps. When you guys say "lightly chamfer" can you give me a more quantitative...
Forum: Cast Boolits
I bought it brand new, have tried casting maybe 200 bullets with it.
I have a PID temperature controller, and have tried it at 50 degree increments from 600 to 850.
I have also tried preheating...
Forum: Cast Boolits
THis is my first experience with an iron mold. My only other one is a lee 9mm, which I've only used a couple times so I'm really new to this.
I am having trouble getting my lyman 314299 to cast...
Forum: Cast Boolits
I would recommend mitutoyo. I have a set and they are really nice, but pricey if you buy new. If you are patient, I would keep my eye on ebay i bet something will come up. I rounded out my tool...
Forum: Cast Boolits
One thing you want to be careful of is to not make the slug too long. I just used a larger diameter bullet, that was maybe .4" long and that proved really difficult once it got into the barrel. ...
Forum: Cast Boolits
Hey,
My k98 bore is a little over .325 (by a few tenths).. but I can't seem to find any .326 size dies anywhere. Should I size .325 or does anyone know where to get a .326 die? I have access...
Forum: CB Loads / Military Rifles
I don't have the gas plug with me right now, but here was what I was thinking about.
Make a new gas plug, with...say 1/4-28 threaded hole concentric to the plug threads (or bigger if it would fit,...
Forum: CB Loads / Military Rifles
This isn't just to save money,most of this is just the joy of experimenting too. I have to disagree with you on powder being the cheapest thing. I don't know where you get your brass and stuff...
Forum: CB Loads / Military Rifles
Well, I did a search on this powder for use in the garand, and most people said it would damage the op-rod. No one mentioned what kind of loads though (not that I noticed, anyway).
Someone made...
Forum: CB Loads / Military Rifles
I did a few chamber castings and got .3095 for the bore. The TE measures at 2.5 but the casting shows that the diameter until the rifling starts is .312 (~.25" from end of case neck). It looks like...
Forum: Military Rifles
Thanks for the replies guys, I appreciate it. I'll go ahead and pick up the book.
I actually sold my ar15 to buy this. I just love the old rifles too much! I'd like to get into serious...
Forum: Military Rifles
Hey,
Anyone have this book? It's kind of expensive at 50 dollars, is it worth it? I just bought a garand and am interested in doing some accurizing and what-not work on it.
Also, would like...
Forum: Gas Checks
Hey,
I've been reading about gas checks, and I'm a bit confused. From what I've read, it seems that the critical factor in using a gas check is velocity, and that the purpose of a gas check is...
Forum: Cast Boolits
CBR, I am using titegroup, not for any particular reason other than it was on sale and uses frugal loads. It smokes a lot though, at least in combination with these bullets, which I've heard other's...
Forum: Cast Boolits
I have been using up some meister TC 122 grain, and I seat them to 1.040" overall length and have not had any problems. That's the length that just barely gets the lube groove completely into the...
Forum: Cast Boolits
Lead Oxide is read and yellow. This doesn't come from experience but from chemistry class, though. I've never had my lead oxidize into that, I would wonder if you have it too hot, or some other...
Forum: Cast Boolits
I understand the twist rate should be slow (as possible for bullet/velocity), can you guys give me anything quantitative about the throat? What kind of throat does well for, say 124 gr truncated...
Forum: Cast Boolits
I can't remember where, maybe it was here, but someone mentioned something about a particular barrel not being good for cast bullets. This raised the question in my mind, what factors make a barrel...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |