Closed ranges where I live as well.
So I tried coating in the cold.
1-4 degrees celsius.
Put 10 kilos og boolits in the oven set at 50 degrees C.
Emptied them into my bucket and coated them...
Type: Posts; User: Graakall
Forum: Coatings and Alternatives
Closed ranges where I live as well.
So I tried coating in the cold.
1-4 degrees celsius.
Put 10 kilos og boolits in the oven set at 50 degrees C.
Emptied them into my bucket and coated them...
Forum: Group Buy Results
Hello.
I'm on the lubegrove list.
Smoothsided with bevelbase please.
Cheers.
Forum: Group Buy Results
Hallo.
8 cavity no lube groove, bevelbase alu mold please.
,358" is fine.
brynjulv dot afdal at gmail dot com
Edit to add adress.
Forum: Group Buy Archives
1 Mold.
Add handles please.
brynjulv dott afdal att gmail dott com
Forum: Coatings and Alternatives
Hardline yes.
Very nice but heavy.
Of ebay.
Do not need to size them.
Just bringing them to Elvira. (My loadmaster.) and go run & gun ipsc.
Forum: Coatings and Alternatives
222678
Coated 50 kilograms 230 grainers in about 2 hours.
7,5 + kgs on each tray.
2. Time coating and sucsess all the way.
Could probably reduce baketime as the thermostat switched off at...
Forum: Group Buy Archives
Hello.
Aluminum or brass?
(Never owned a brassmold but I can fellow instructions.)
Forum: Group Buy Archives
would be nice.
Forum: Group Buy Archives
How does the boolit perform at ppc for the swede?
Forum: Group Buy Archives
Very nice.
Possible to add MP mold handles?
No 4 on the list. brynjulv dott afdal att gmail dott commercial.
(also sent a pm about this earlier.)
Sincerly.
Forum: Group Buy Archives
6 cavity aluminum no lube grove, bevelbase, 153 grains.
brynjulv.afdal att gmail dot commercial.
Please.
Forum: Coatings and Alternatives
Hi.
Going to coat my first batch of 230 grs, 452 rn boolits.
Brick red..
5 milliliters mix pr 2 kg boolits.
Surfacearea/kg must vary between 45 230 grs and 115 9mm.
Any input on this?
...
Forum: Lead and Lead Alloys
Found an old report on alloys with bismuth.
http://nvlpubs.nist.gov/nistpubs/jres/5/jresv5n5p1085_A2b.pdf
I hope it's useful.
As title says.
Got a Lee ,452-228-1r that has given me 10.000+ good boolits for my S&W 625.
want to drill out most of the lubegroves as I'm currently coating instead of lubing.
Hope to gain:...
Forum: Casting Equipment
71525It's easier to drop a boolit into hole than setting it on a pin.
Mounting the press upside down also lets you size base first.
Forum: Cast Boolits
I think it's solved.
Worn cylinder stop and fast da shooting.
The leading has gotten worse as the play has increased.
No leading in my new 625 PC and I'm currently waiting for a new cs for my...
Forum: Cast Boolits
Thank You all for the useful advises.
I use LEE liquid allox lube.
There is lube in the barrel after shooting and it cleans out with a oiled swab. Thats when the lead deposits become visible. ...
Forum: Cast Boolits
230 grs TC TL.
IŽll give it a try.
Thank you very much.
Forum: Cast Boolits
Hello.
IŽve fired ca 4000 lee 228 grs 1-r bullets in a 5" version this season.
Throat to barrel dimensions and timing is ok.
No frame choke.
There is leading if alloy hardeness at brinell 12 or...
Forum: Cast Boolits
Ca 30 kilograms of Lee ,452 228-1r for my revolver.
The alloy makes them 231,5 grains and hardness is softer than 3b and harder than 4b on the Staedtler scale.
Works great in my 625 S&W.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |