Search:

WTS .223 / 5.56 brass to reload 15lbs $105 shipped
USPS money order, thank y’all.

I have a book that states 4.2 max tb,

My Lee disk .95 throws 4.4 gr my lee 1.02 throws 4.8 gr

both feel good, but that 4.8gr seems to have just a better grouping.

Pistol is a S&W 19-3,...

The red-line bullet mfg calls them "hard cast" and max velocity is 1200 fps, they told me Not to use mag pistol powders with their bullets. I pulled a few bullets and noticed that they were under...

leading looks like a groove in the barrel is full / dirty with lead. If you run a brass bristle brush or some stainless steel wool wrapped brush down your bore and scrub, small flakes of shiny lead...

Excellent, Thank you all for the input. It is an S&W m19 6", I will try and pull down a loaded round and see what the bullet diameter is after loading, and see if an unloaded bullet will fit down...

So I was loading Red Line 158 swc .358 cast bullets, Hogdon Universal powder 4.4gr and after 30 rounds I had some moderate lead deposits about the first 1" of my barrel. Is that an indication of...

Had the same issue, this guy makes all the shim's you will ever need, great small buss.

http://triggershims.com/

good stuff!

No i need to figure out why my police positive is punching...

357 Mag load data:
WC820 (new) powder, 125 grain JHP, Fed SP Mag primer 17.2 gr = 1405 fps @ 1.570" 6" S&W

WC820 new 158 gr bear creek SWC 12.5gr 1165 fps spm 6" S&W

$11 a pound pistol powder, where are you now... Rex come back!

So i used a table spoon of minwax paste wax and a tea spoon + of Allox, seems good now, way softer, try out and let you know.

I will see if I have any STP or ATF but maybe lee allox? That i do have.. Thanks

Any idea if i can cut the blue lube with anything to make it pan-lube material? It's hard as a rock when it dries. Any ideas would be great, thanks!

Thanks, I will give it a go!

Anyone load 700 grain or hollow point heads with Trail boss? I'm looking for any data, thanks

.380 acp 100 gr plated RNFP 3.4gr CSB-1 @ .980" = great shooting load.

I was just loading them to the crimp groove,

I have used gas checks on mine but Lee Alox lube, going to try and pan lube them next, no lead signs but did not chrony them yet

Fired just fine, well like you would expect, hard hitting with 25gr H110 for the FP, had some unburnt powder in the barrel with the 26 gr H110 in the 625 gr HP, 15 rounds was all i could take, snow...

I Found out CBC Brass has thicker wall , Flare it well enough to accept the base, then final crimp you can see the driving bands as a ghost image. I used Hornaday and this problem went away.
...

Anyone ever reload CBC head stamp Brass for the 500 S&W? Seems VERY hard to seat the bullet in the case, anyone?

So his is already smoked and broken in? run over and hang out with him a few hours, keep yours new when it come in! :)

My HP weighed in at 625 gr so I went ahead and loaded them with 26 grs of H 110, see what happens this weekend, If no reports follows, 26 grs is too much

Any Load Data? Looking to use AA#9 / H 110 or Titegroup for the checked ones


Can I shoot some without the gas check using Trail Boss??

Any data would be great! Thanks!

any rules on sending lead to Canada?

LOOK WHAT I FOUND when i got home!! BIG BIG And they ARE BIG!

http://i170.photobucket.com/albums/u267/NEWCALSHOOTER/100_3110.jpg

...

Sadness? Should be a great surprise! the 700 Gr must be so big the USPS is inspecting it for a possible WMD connection! :)