Hi All,
I have been reading this post with fear and trepidation!! I am greatly concerned about possible repercussions for some of you, but suppose I should get to the point.
Do not shoot any...
Type: Posts; User: Gandolf
Forum: Cast Boolits
Hi All,
I have been reading this post with fear and trepidation!! I am greatly concerned about possible repercussions for some of you, but suppose I should get to the point.
Do not shoot any...
Forum: Cast Boolits
Hi Floodgate,
Nope, I wasn't in a movie, but Gandalf was.
I had read the Hobit books several years ago and was looking for a name to use on the old virtual fly shop fly tying bulletin board....
Forum: Cast Boolits
Hi Bpost 1958,
I can make a wild guess as to the XRF devise works, and maybe if need be, Johnly can correct any errors that I make. The only drawback is that my explanation, even if I'm...
Forum: Cast Boolits
Hi All,
I'm 57. Two daughters, one of whom likes shooting.
Regards,
Gandolf
Forum: CB Loads / Military Rifles
Hi All,
I was at a gun show today, and saw a 1917 Enfield that had a very good bore. The lands and grooves look sharp and crisp right up to where they join the leade. The bore looks a bit...
Hi All,
I have a borrowed set of 6.5X55 true line jr. dies that I want to try in a tong tool. The only die I want to try is the seater.
Which handle do I use? How do I tell the handles...
Forum: Cast Boolits
HI All,
I did not communicate the seating problem well.
The problem is that the bullet will not fit up into the seating die. The bullet is just enough bigger in diameter than a standard...
Forum: Cast Boolits
Hi All,
A friend has a set of Lyman "True-line" dies. They say "True-line" on the box.
It seems to me that these dies also fit the Lyman Tong tool. Is this correct.
I was thinking of...
Forum: Cast Boolits
Hi Jleneave,
You would use a lead hammer to drive on something you did not want to mar. The lead carries a pretty good whamp, but is soft so it won't dent or mar a piece the way a hard lick...
Forum: Cast Boolits
Hi All,
A co-worker is wanting to buy a MN, since he already has brass and dies (he used to have one.) I told him that I had read that the Fins were the most accurate of the MNs, and normally...
Forum: Cast Boolits
Hi All,
A co-worker would like to buy a Mosin N. He had one, but it shot very poorly, but still has the brass and dies.
I told him that I had read that the Fin MN. shot the best of all of...
Forum: Gas Checks
Hi All,
Years ago I ran a stretch press at an aircraft manufacturer, and some of the alloys we used would be strong enough for gas checks, IMHO.
However, that doesn't solve the galling...
Forum: Cast Boolits
Hi All,
I have been a lurker for a while.
A few years ago I started casting for a while but gave up and am now planning to try it again.
I bought and read (the covers off) the Lyman 44th...
Forum: CB Loads / Military Rifles
Hi all,
I have a 6.5x55 Swede that has an oversize bore. In a post on this same subject, it was stated that Lee will make a collet die to a specific size.
My question is: If the bore on my...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |