You can use a 35 REM Lee collet neck sizer die for a 358 WIN by using a .090 washer between the shell holder and the die. Just a large enough hole to slip over the top of the cartridge. A taller...
Type: Posts; User: Shakey Jakey
You can use a 35 REM Lee collet neck sizer die for a 358 WIN by using a .090 washer between the shell holder and the die. Just a large enough hole to slip over the top of the cartridge. A taller...
Djones, Did you get a chance to try the 35 Rem/Lee collet die trick yet?
Heres one right here, $250 to JES, a scope, and you are good to go.
http://www.gunbroker.com/Auction/ViewItem.aspx?Item=412525067
This is getting a bit off topic but I also picked up a long action 30-06 Savage 110 with a Bushnell 3200 Elite scope for 217.00. The PO had tried to paint a camo pattern on it with what looks like...
I just accidentally picked up a stainless model 11 on GB for about 300. It has the detachable mag, anybody have any experience with those?
Every time I build something based on a Savage I wish I would have splurged on an FN Winchester. Not hating on Savage, they make a decent gun, just wish I would have not been so cheap. I wouldnt even...
Yes, aluminum pillars and Devcon bedding compound.
Forum: Hunting with CB's
The Lee collet neck sizer die for the 35 REM works great for the 358 WIN with a .090 thick flat washer placed between it and the shell holder. Slick and cheap.
I bought a walnut Boyds platinum with wrap around checkering.
Mine is a model 10, was a 243 sporter, bored and chopped by JES. Almost done, I'll have pics up in a couple of weeks. I went that way as it is the only practical way I could find to avoid the varmint...
Forum: Hunting with CB's
Legislation is working its way thru to allow straight wall pistol cartridges in southern Michigan. My Remington 788 44 mag is chomping at the bit!
Forum: Hunting with CB's
Check out the video on this page: http://bulletin.accurateshooter.com/?s=sauer&submit=Search
Forum: Factory Rifles
Internet, accu trigger, plastic stock, blind mag. Will cost about 350 after shipping, fees and taxes are pd. Probably what I would consider minimum quality to base a project on. The previous posters...
Forum: Factory Rifles
Just picked up a Savage model 10 243. Sending it to JES, wont even shoot it beforehand. I paid about 300 for it.
Forum: Hunting with CB's
That same load gives about 1700+ in my 94, and VERY accurate to boot.
Feed without issue thru my Savage 110 '06 staggered feed.
Forum: Casting Equipment
I do it like Buckshot does except I use 320 and 600 lapping compound instead of the sandpaper. Couldnt be easier.
Forum: Factory & Surplus Powder
68456Small can of Red Dot, 1971, Jay's Gun Shop, when Jay was selling out of his garage in Clare Michigan. Still have most of the can!
Forum: Factory & Surplus Powder
I just posted some blue dot results in the thread "NOE 225-70" in group buy results. Just what you are looking for.
Forum: Reloading Equipment
I need a cheap electronic scale to sort boolits on. Have no desire to weigh powder with it as I have an RCBS (Ohaus) that is part of the family. I see 3 or 4 of them out there and Midway even has 2...
Forum: Casting Equipment
Clean the moulds using electrolysis. Dont touch them with a brush. There is a recent thread in this section.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |