Search:

The Model 64 was produced with the original tapered barrel only during the first couple years of its production. I have one. IIRC there was a post on the S&W Forum stating they were made with the...

8 grains of Power Pistol is under 16,000 psi according to Quickload. This was ran with a NOE 429421 that weighed 263 grains with my alloy.

The load was taken from the above inked Brian Pierce...

Ditto. Shoots better than anything else in both my 6.5 inch and 4 inch .44 Specials. Look no further with a 250-265 grain SWC.

It happens to all of us. Father time is a cruel master. Mike and I were just discussing the eyesight issue this evening. I had better than 20/20 eyesight into my early 30's. When shooting iron...

Question answered by PM.

Last night after Mike called me and asked me to get on this thread and post the results achieved thus far with my 03A3 Springfield I took a few hours to mull it over. Problems I had with even...

357maximum is way to kind.[smilie=s:

My rifle is a CMP Greek return Remington made 03A3 produced in May, 1943; with a brand new (in the wrapper & cosmo'd when I bought it) Remington made July of...

I have a .500 S&W Handi-Rifle and shoot it as a "poor man's 50-70." No rompin' stompin' loads for this kid!

My booilt of choice is the Accurate Molds 50-440N (plain based), which Tom designed for...

Here's a link to my group buy for the ACE 7mm Heavy designed by Badgeredd. Hope this helps.

http://castboolits.gunloads.com/showthread.php?239641

I just started and interest thread for a Group Buy of a 7mm 170 grn bore rider gas checked design by Badgeredd. Molds will be cut by A.C.E.

There will be four paired band/nose diameters to choose...

Update -

I have a Group Buy interest thread started on this design. We will not be using Ballisti-Cast to produce these molds. These molds will be cut by Josh at A.C.E.

Also, there will be...

3x may not seem like much by todays standards but I can tell you that with the same scope on a .44 Magnum carbine 150-200 yards works just fine. I have shot out to 300 yards with that setup and not...

I have a couple of the Weaver V-3 1-3x20 scopes mounted on pistol caliber carbines and I agree it is a great little scope. Perfect for woods hunting and 4" of eye relief would definitely make it a...

Burris made the 1-4x Intermediate Eye Relief Scope back in the late 90's - early 2000's. I bought 2 of them and they are great for the hard kickers. I have them mounted on an H&R .450 Marlin single...

Going to a powder with a slower burn rate than normal for a particular cartridge is a trade off. You get a gentler start and better case fill, but at the cost of higher muzzle pressure which can...

Quickload will show you what the real differences are. Western Powders has it backwards.

Same here. Birch Run is almost always a waste of time. Not sure if the Midland County Fairgrounds still puts one on or not. The show run by the Midland Gun Collectors Assn. at the old Midland...

I've also heard that one a few times before. My response is the same every time. "Is that what the Commissar told you to say?" Usually I get a blank stare in return. So I just stare them back...

Nrut-

I just got done casting over 450 of these buggers. Brought 10 of them inside and took some measurements.

The nose does not taper down from .270" to .265" just above the top lube groove. ...

When this limited buy was ran I missed it as well. I contacted swedenelson and he had this one two cavity mold left over, which I bought from him. I have not yet cast any for my 6.5x53R, but I plan...

101126

I have a 2 cavity version of this design which was cut as a limited run by NOE a couple of years ago.

Very soon I'll be testing it in my sporterized 1895 Dutch Carbine chambered in...

Neat, can't wait to see it in person!:awesome:

One thing about these "copper enhanced alloys" that I found out right from the start; 700* - 750* and use the ladle, not the bottom pour. You will be very happy with the results.

My pot is set...

Good post, John. This one should be required reading, especially for the touch screen phone generation. I'm sure he had one of those that he had big bucks invested in. Probably had spent a lot...

I just knew you couldn't resist developing a 2,000 fps load for that thing!:lol: How many woodchucks you shot with that load so far? Or are they all still hidin' over in the next township?:kidding: