The clays worked just fine. Seemed to burn cleaner than the unique ever did as well! At 50 yards I got 7 into about 2" with 3 hitting left and low a few inches and flying sideways.
Type: Posts; User: Loki610
Forum: Factory & Surplus Powder
The clays worked just fine. Seemed to burn cleaner than the unique ever did as well! At 50 yards I got 7 into about 2" with 3 hitting left and low a few inches and flying sideways.
Forum: Factory & Surplus Powder
With this rifle I'd be happy to get a consistent 12" group at 100 yards! It's an old martini enfield with a pitted bore, shoots factory ammo about 2' high and right at 100. Last week my best group...
Forum: Factory & Surplus Powder
Thanks for the help! I got 10 rounds loaded for the .303 with 10 grains and I'll give them a try tomorrow night.
Forum: Factory & Surplus Powder
I'm all out of unique and can't get anything locally anymore but I have 4lbs of clays I got in a trade a few years ago.
I couldn't find any rifle loads listed with this powder so any advice would be...
Forum: Single Shot Guns
None at all actually! the holes were so close to what I needed it only took a few strokes with a small file to get it lined up properly. The short screw it came with fit perfectly but the tang screw...
Forum: Single Shot Guns
OK I got the lyman #2 '94 tang in the mail! Got it mounted last night and finished making a front sight. I filed down a piece of bar stock to make a dovetail, drilled a hole and threaded in a screw...
Forum: Cast Boolits
load em backwards and have some fun with gophers/prairie dogs! I think I used 2.4grains of clays in my .38 special. I still have well over 1k of these to load from a trade I did a few years ago.
Forum: Single Shot Guns
I'll have to call them and find out if they will ship to Canada without me having several weeks of paperwork.
Forum: Single Shot Guns
Should have specified that it's the sight for the 1894 I ordered. I need 2.17" hole spacing so I may have to adjust the holes in the sight base a little if it's 2.25"
Forum: Single Shot Guns
I've got on order what must be the last lyman #2 in canada from wholesale sports, they're no longer going to be a distributor.
If anyone has one of these could I get you to measure the distance...
Forum: Single Shot Guns
Well so far I'm screwed, I cant get nothing. At least not in the next couple of months!
There is no marbles sights in stock at any of the canadian distributors and they figure it'll be months...
Forum: Single Shot Guns
The half inch is the base measurement not the opening, never did measure to the other hole, and yes its threaded.
Forum: Single Shot Guns
So if I go with one of the marbles sights from Brownells, is there some sort of formula for calculating front sight height?
579-009-808WB
Win. 1894, 55, 64, 1853, 1885, 1892 (original)
Mfr...
Forum: Single Shot Guns
I have measurements and more pictures for you guys. Full barrel length is 27" with 23 3/4" center to center between the barrel dovetails. Muzzle dovetail is .39 inches and back end is .5 inch...
Forum: Single Shot Guns
Doesn't look like it would work, my rear dovetail is so close to the receiver that the elevator hangs over the action!
Forum: Single Shot Guns
Sorry its in 45-70!
Best picture I have right now, I can take more tonight after work.
67764
Forum: Single Shot Guns
So I have this original 1885 winchester thats on loan to me from the father-in-law. Its got a new 27" custom barrel on it with 0 taper and some kind of horrible homemade tube sight! I took it out...
Forum: Single Shot Guns
I have one that has seen its fair share of corrosive rounds and minimal cleaning! It took me weeks with wipeout to clear all the copper layers/old powder out of my grandpas favorite bear rifle. ...
Forum: Single Shot Guns
I'm really considering getting one of these rifles but I cant find any information on pressure loads these will take. I'm not likely to hunt with it so it will be mostly used for plinking loads, but...
Forum: Hunting with CB's
I can understand your worries! With the frozen ground right now they ricochet terribly. My inlaws live in Swift Current and she's pretty flat there!
Not much of a worry for me since I live in the...
Forum: Hunting with CB's
The richardson's are quite small, just makes it more of a challenge with the old rifles.
Forum: Hunting with CB's
Getting ready for gopher season and I thought I'd post a picture of my current favorites.
18-30-30 front centre is Speer 110gr HP with 35 grains of varget
100- 30-30 pile on the left is lee...
Forum: Cast Boolits
x10 on the lee 105grain
I got one in a 2 cavity to try and its great! not the most accurate but the girls at the range seem to love shooting it. I load it in front of 2.5grains clays, no idea of...
I finally got around to measuring the diameter of the cavity and its about .46
Forum: Cast Boolits
Since I started 2 months ago I'm nearly at 10 including the old civil war era mold I found.
6 for the .38 including the 000 buck mold
2 for the 30-30
1 for a unknown .46cal muzzleloading rifle
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |