Master caster - $1800AUD
Pickup only from Burpengary, QLD 4505
I have a master caster I am wishing to sell. It comes with a set of 135gr TC 9mm molds, which are rust free inside. It has had the...
Type: Posts; User: Gatch
Forum: Swappin & Sellin
Master caster - $1800AUD
Pickup only from Burpengary, QLD 4505
I have a master caster I am wishing to sell. It comes with a set of 135gr TC 9mm molds, which are rust free inside. It has had the...
Forum: Deep Theological Discussion
I was under the impression the gospels were written by people?
Or if you want to be literal, gospel is the truth.
Forum: Coatings and Alternatives
Hi team
Haven't been on in a while. Anyway, I purchased a mastercaster and got it running sweet. Made a few bullets and coated them in (cant remember which type) gold hitek. They look mint, smash...
Forum: The Star Equipment Corner
I didn't run a multimeter over it. I removed the thermostat and had it connected live and neutral only. Let it get to about 200C then switched off and let it cool down. Connected groynd wired and...
Forum: The Star Equipment Corner
I super appreciate your input gentlemen.
Forum: The Star Equipment Corner
I think I am using the same. Someone posted a link on another thread to one they had used and I think it might be that. Costs $20-25 off ebay. I've hooked up two already and have another two at home,...
Forum: The Star Equipment Corner
I'm not super savvy when it comes to using a multimeter so you'll see me ask lots of questions. When you say check for a short, that would mean low resistance between the pot and the coil? Whereas if...
Forum: The Star Equipment Corner
Ok I understand. Probably a good time to install a pid then..
Forum: The Star Equipment Corner
Now is it possible that there's so much earth leakage from a moist heating element that it would trip my circuit breaker?
If so what would be the next step? Remove the pot and run the heater...
Forum: The Star Equipment Corner
Turns out the earth wire was not connected inside the machine. That's all it was.
Forum: The Star Equipment Corner
I've taken the machine in to work. Hopefully one of the bright sparks will have a look over it today.
Forum: The Star Equipment Corner
Sorry I should have explained better. When I said buzz I mean I can feel a tingling sensation when I touch the black shroud on the outside of the pot. Also when I touch the pour lever.
Forum: The Star Equipment Corner
Hi guys
I recently purchased a master caster and had it shipped to australia. So it'll be running on 240v 50hz instead of 110v 60hz. I've got the plug wired correctly but noticed I get a bit of a...
Forum: Casting Equipment
My last 358 mold from mihec had a similar problem. The pins were sliding out when they get hot. I've only used it twice. I suppose I should contact mp before whinging.
Forum: Cast Boolits
I'm using the mp 130gr rnbb. Though I'm having trouble with it leaving crud in my barrel. Though I believe that's got something to do with the way I'm casting or using hitek rather than any inherent...
Forum: Cast Boolits
I can attest. I have a xl650 and am working through loading cast for 9mm. I had issues with the boolits swaging down using the stock powder funnel, until I machined one up that has an OD of .356 and...
Forum: Cast Boolits
I'm 33, just started this year. I got interested because I'd like to keep ammo cost for shooting ipsc down. But now that I've gotten into shooting, I can't wait to purchase some bigger calibers to...
Forum: Coatings and Alternatives
Wire it into the heater element so that the fans not switching on and off. Apparently that's bad for them.
That's all the wisdom I have.
Forum: Coatings and Alternatives
I used 4.1gr of hodgdon universal. I was using ap70 before that. I only asked because some seemed to smoke more than others.
Yes this was foundry lead I tried. I'm yet to try foundry without acid...
Forum: Coatings and Alternatives
I loaded and shot 50 cast 130gr 9mm. The leading in my barrel cleaned up significantly after washing the bullets in hcl before coating and baking. Definitely a massive improvement since my last test...
Forum: Coatings and Alternatives
Thats lucky. I have the 125gr tc mold on order with the master cast :)
Forum: Coatings and Alternatives
https://www.mp-molds.com/e-shop/molds/alternative-coating-molds/9mm-38-147-rn-bb-6-cav-brass-nlg-mold
I also bought this one from mp.
...
Forum: Coatings and Alternatives
If you purchase some, dilute it. It goes a LONG way
Forum: Coatings and Alternatives
That's good feedback. Thanks mate
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |