how in the world do you accomplish that COL, either I have an awful tight chamber or the rest of them are really loose, that bullet, in my mold at least drops 309 forward of the crimp ( that's about...
Type: Posts; User: georgerc
Forum: Cast Boolits
how in the world do you accomplish that COL, either I have an awful tight chamber or the rest of them are really loose, that bullet, in my mold at least drops 309 forward of the crimp ( that's about...
Forum: Coatings and Alternatives
here's an odd discovery, today I done some casting, and threw those 3 squibs in there, and guess what, they floated, didn't melt, not sure what temp I had but my Lee 10 lbs was at about 4, all the...
Forum: Coatings and Alternatives
the squibs were plated boolits, I think I am on to something there but every time I question published data I get **** for it, the hodgdon data I used appears to be a bit funky, same charge for a...
Forum: Cast Boolits
I must have been casting cold as most of mine are oversized, heavier than advertised too, not to rule out the lee mold isn't perfect but this was the first time, I remember seeing them frost up and...
Forum: Coatings and Alternatives
well I had a chance to do a bit of target practice today, had 18 of those rounds, lee 358-125 rf, about 130gr actually, 3.6 gr of titegroup, pretty good combo, I like them, also had some of those...
Forum: Coatings and Alternatives
I understand thet just with the 38 caliber its an animal in itself, a 38 apecial 125 gr with titegroup for example, I believe it calls for 3.2-3.8 gr, same bullet +P calls for 5 gr, same bullet in a...
Forum: Coatings and Alternatives
yeah I'm done with those rounds, I got 10 more, I'm just going to pull those, they were my first loads figured I'd start low and avoid blowing up, got some 42 more HP with a smidge more powder, I...
Forum: Cast Boolits
a note on the equipment, it may seem overwhelming when you look at what other people are doing, keep in mind they have been at it for a while and accumulated this stuff over time, you don't need all...
Forum: Coatings and Alternatives
thanks for the tip, I have yet to load any of the ones I made but I will look for those streaks, is that pretty much an indication of PC fouling? any other signs?
I have been watching them as they...
Forum: Coatings and Alternatives
oh and about the baking, I got impatient I did not have a oven thermometer, I did the first batch at 400 they worked fine but I noticed the PC started melting a good while before the oven temp was...
Forum: Coatings and Alternatives
I use the powderthru expanding die with the autodrum on top and yes I expand the case while throwing a charge at the same time, I weigh the case prior, zero out the scale and verify every charge...
Forum: Coatings and Alternatives
I have to concur with the previous post, #5 container and black bbs, first time did pretty good, had some imprefections but mostly due to me being clumsy, one thing I noticed in that first pic, the...
Forum: Coatings and Alternatives
I use a single stage with a lee auto drum, I weigh the case first, zero it out and charge than weigh again using a cheap Hornady digital scale, if I am off by a tenth of a grain I dump it and throw...
Forum: Coatings and Alternatives
I have lots of titegroup on hand, matter of fact it is all I used so far, I weigh all of my charges and make sure they are consistent to a tenth of a grain,I previously loaded some berrys plated 125...
Forum: Coatings and Alternatives
for whatever reason I can't post a picture, may be something wrong on my end, anyways, I got my 358 sizing die, pushed some through and they came out to about 357-357.5, then I powdercoated them HF...
Forum: Cast Boolits
000, it went fairly easy, the 9mm .355 was a little hard to pound through, the .380 went right through, .358 barely even left an impression
Forum: Cast Boolits
yeah I read about the dowel and sandpaper method, I have access to mills and lathes, just for $20 figured I'll just get one, plus it comes with a bottle of allox
Forum: Coatings and Alternatives
can you elaborate a bit on this, for example one of my projects is loading for a 357 revolver, I slugged it right at 357, I have previously loaded plated bullets for it using cast data, for the most...
Forum: Cast Boolits
oh wait, .356 , 357, .358 are the only Lee options, guess .358 it is, wont it be a little too big for the .355? especially with the powder coat, considering the sizing is done after.
Forum: Coatings and Alternatives
how much does the PC add to the diameter? the .002 oversize still applies, does not shave the PC?
Forum: Coatings and Alternatives
I should probably ask this question here, how do you treat PC boolits? as cast, jacketed or somewhere in between?
I loaded jacketed and plated, never cast, read about flaring the case mouth a bit...
Forum: Cast Boolits
do you run them in a 9mm that slugs .355? I love the idea of one size does all but Lee dies are cheap, I can afford a couple just figured there are 4 sizes avail, I believe, what would be a better...
Forum: Cast Boolits
I'm a little compulsive about shooting cast, my first experience with cast bullets were the PPU 38 specials, I bought 500 rounds, still have most of them, they lead the snot out of my revolver in a...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |