That is a partial (or maybe complete) serial number that was used during manufacture to keep fitted parts together...
As Pietro pointed out, the actual serial number will be on the bottom, either...
Type: Posts; User: Salmoneye
Forum: Leverguns
That is a partial (or maybe complete) serial number that was used during manufacture to keep fitted parts together...
As Pietro pointed out, the actual serial number will be on the bottom, either...
Forum: Leverguns
The two piece firing pin is a 'safety'...
When the gun is out of battery, a following hammer can not force the pin to ride on the primer...
One piece pin does indeed lighten cycling, but you...
Forum: Leverguns
Both my 2003 1894PG and 1990 Marlin 1894S will eat anything (almost), including SWC and my flush loaded rat shot loads in .44 Mag cases...
Only time I have a hitch in my git-along is if I try to...
Forum: Leverguns
I can keep that load on a 9" skillet all day long at 50 yards with my 26" barreled Marlin 1893...
I seat the .310" ball flush in the case, and they load fine from the magazine...
Pure heck on...
Forum: Leverguns
I'll take a New Haven made Marlin over most North Haven, and certainly over all Ilion made...
Don't buy Hornady ammo with short cases...
Problem solved...
Been loading a 158gr boolit/bullet over 5gr of Red Dot in .357 for 30+ years...
First load I tried off the included sheet that came when I bought my Lee dies...
Forum: Leverguns
First thing that struck me also...
Should have loaded the mag then racked one into the chamber...
Forum: Leverguns
If you're limited to 1,400fps and under, here is some data for you using 170gr cast...
http://www.gmdr.com/lever/lowveldata.htm
And here is just one of many suppliers that have cast larger than...
Forum: Leverguns
Uh...
Because SAAMI barrel specs for .44 Mag Rifle are not the same as .44 Mag Pistol/Revolver...
Pistol groove is .429"
Rifle groove diameter is .431"
Forum: Leverguns
The 'custom shop' was discussed on another board last week...
http://www.marlinowners.com/forum/336/263538-marlin-custom-shop-open-again.html
The conclusion is that it is Dakota Arms which is...
Forum: Leverguns
Thanks for the info...
I also have been wondering about the performance of the .358" coated in micro-groove vs. traditionally lubed cast at .360"...
Still not sure why the bullet companies...
This link may help:
http://www.imfdb.org/wiki/Seraphim_Falls
Internet Movie Firearms Data Base
Nice!
I'm glad you picked it up...
Remember, if you get the hankering to put a scope on it, the link to the info on how to make the new Millet rings work for ya, is in your other thread...
My Albion Enfield will pass .357" Jacketed, while .358" cast must be gently pushed through...
Over .358" is tight...
I have been shooting 158gr .358" cast with excellent results for years...
On the right day, with the right buyer, WITH the rings...
Rings are not made the same any longer, and though the new style can be reshaped to work, they are not an off the shelf fit...
Post #33...
The 686-3 with the factory broached/scalloped rib came with specific Millet rings...They were only made in 8-3/8"...I believe there were only 1,100 made...
Last one I saw on GunBroker with box,...
Forum: Leverguns
I think you mean North Haven...
Marlin has not been in New Haven since ~1970...
Forum: Leverguns
The reason Marlin uses 1:38" twist and .431" groove, is these are the SAAMI specs for .44 Magnum in a rifle...
160664
SAAMI spec for .44 mag pistol is 1:20" and .429 groove:
160665
I am...
My Albion Motors Enfield No2 Mk1** has .356" throats...
I load 158gr Truncated Cone boolits from Penn @.358" using .38spcl dies...
The load I use is 2gr Red Dot...This is from the old Lyman...
Forum: Leverguns
'Whiting' is nothing more than chalk (Calcium Carbonate)...
Forum: Leverguns
Hmm...
This would make my S&W Model 1913 in .35 S&W Automatic an 'antique'...
Forum: Leverguns
Lets look at that...
The Brenneke Black Magic 1-3/8oz slug (appx 600gr for rifled or smooth bore):
Velocity 1,500 fps
Energy 3,014 ft/lbs
Momentum 128
TKO 93
Now a couple of .45-70 loads...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |