210160
Tried powder coating and most of the bullets sized very easy, but some didn't and have bare spots. I keep reading that even though you have bare spots from the wire racks, that the powder...
Type: Posts; User: atygrit
Forum: Coatings and Alternatives
210160
Tried powder coating and most of the bullets sized very easy, but some didn't and have bare spots. I keep reading that even though you have bare spots from the wire racks, that the powder...
Forum: Casting Equipment
An update. I purchased the mold through Amazon and I was able to return it. It was fun explaining to the guy that sounded like he was from overseas what was wrong with the bullet mold.;-)
The...
Forum: Coatings and Alternatives
I successfully coated twice, then sized and coated for a third time. Are you guys sizing again, or just using them as is.
Forum: Casting Equipment
The list of bullets were without coating, I just had a picture of one of the bullets with coating. Also, using 92-6-2 lead for the bullets.
Forum: Casting Equipment
I have a new .356, 6 cavity bullet mold that is producing oversized and out of round bullets.
Out of probably 1,500 that I cast in one session, I measured a sample of 50 bullets.
.358 ...
Forum: Coatings and Alternatives
174305
I have FINALLY been able to get this to work. I followed Ausglock's recipe, 2 kilos with 6 ml of black gold. They are not silky smooth, so I probably shook them a little too long, but not...
Forum: Coatings and Alternatives
Thank you for the observation because I now think you are correct. I ran a cleaning patch after scrubbing the barrel and I see a few slivers of lead.
Forum: Coatings and Alternatives
I am STILL having issues with the coating coming off in my 45 and 9mm barrels. First I tried my own coated bullets then ordered from two manufacturers to see if it was my bullets, and I'm still...
Forum: Coatings and Alternatives
Yes, only the wind was blowing in right back at me. :-)
Forum: Coatings and Alternatives
Finally success...at least what I'm going to call success. I received my replacement bullets and they worked MUCH better than the first ones I received. I have just a little bit of the coating...
Forum: Coatings and Alternatives
I was able to get my order replaced, so I'm a happy man.
Forum: Coatings and Alternatives
That is what I was thinking could be the issue, but I have an email in to the commercial caster, so I don't want to say at this time.
Forum: Coatings and Alternatives
117822117823117824117825117826
I have had nothing but problems with this coating and I realize this is a learning process, but I got frustrated with it and decided to just buy some bullets that...
Forum: Coatings and Alternatives
My oven is also a convection.
Forum: Coatings and Alternatives
Yes, I let the oven preheat to 400deg F.
Forum: Coatings and Alternatives
111575111576111577111578111579111580
Here is my setup showing 400 degrees and 5 pictures of the wipe test from 10 minutes to 14 minutes. I did this over two nights, so the 10 and 11 minute tests...
Forum: Coatings and Alternatives
Thank you very much for the offer.
What I'm doing is what i should have done a long time ago, which is bake for 10 minutes, then 11, 12, etc. all the while doing the wipe tests. Last night I...
Forum: Coatings and Alternatives
All of the coating doesn't come off when I do the wipe test, just some of it. So I don't think I could "wash" them and have clean bullets to recoat.
Forum: Coatings and Alternatives
111360
This is Black 1035 baked for 15 minutes at 375 with 1cc per pound and failing the wipe test. I don't really see a difference in the coating from when I baked at a higher temperature. ...
Forum: Coatings and Alternatives
1. 10 minutes or so.
2. Approximately 15 minutes with a fan. The temperature was great, probably 90 degrees Fahrenheit and low humidity.
3. I ran the 1st batch at 395 Fahrenheit for 10 minutes and...
Forum: Coatings and Alternatives
OK, I'm STILL having problems with this coating! I purchased the new powder (way easier to mix [smilie=p:), specifically Black 1035 from Gateway Bullets, which I received it in one day, which is...
Forum: Coatings and Alternatives
103976
This is what the barrel looks like after 50 rounds and running a bore snake through the barrel a few times. I'm not sure if it is "bonding" to the barrel, but it is a royal pain to remove...
Forum: Coatings and Alternatives
I used the oven as an excuse to build a PID controller. I figured I could use it for lead casting and the oven. But before that I was using an oven thermometer I purchased from Wal-Mart.
Also, I...
Forum: Coatings and Alternatives
I'm using Wal-Mart brand acetone.
I don't remember what my barrel slugged at, but I remember it being OK. I pull a bullet after reloading and size it. I don't expect it to be swagged down, I'm...
Forum: Coatings and Alternatives
103961
5-1-7 mix
1 ml per pound
1 pound in the oven
200 Celsius for 10 and 12 minutes same results.
I'm getting very, very frustrated with the black Hi-Tech coating. I have been trying to get...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |