Search:

Browning gun museum is in Ogden Utah with original prototypes, etc. Everything Browning is there.

Some Mexican restaurants that I go to, if you request, will grill a couple good sized jalapenos to go along with your meal. Just hold by the stem to eat, they are usually very hot and make my ears &...

Thanks Sam, your camera takes a very sharp picture indeed! Nice gun, I suspect that you will get some serious interest in it, hope need not be listed for very long. Good luck, thanks for the picture....

Well? Where is your photo for the above post? Lets see one!

It absolutely will reduce the amount of smoke after each shot. You will be happy with the all around results of powder coated boolits.

Try this for rifle boolits down to .22. Collect plastic cartridge trays with square grids that come with boxes of 50 hand gun cartridges. 40 cal. works for .30-.277 size boolits, 9mm or smaller...

Please explain what " high carbon alloy" is related to lead boolits. I know what that is related to steel.

For 27 and 30 cal. boolits I have taken plastic .45 trays w/ the 50 square grids that factory amo comes in and drill holes in the centers of each grid using a 11/32" - 3/8", sharp, brad point drill...

Bore size is the barrel measured inside the lands of the rifling, grove size, or I-2 thousandth over grove size dimension is what the boolit should be sized to. Anyway this is my understanding of...

I have cast .30 boolits of COWW and powder coated them. After curing at 400 for 10 minutes in the convection toaster oven, I dropped them directly from the oven into a 5 gallon bucket of tap water....

Buckshot on this forum makes nose sizing die bodies for RCBS and Lyman lubesizers. Nose sizing bushings, which are really neck sizing bushings are made by RCBS and others and can be gotten from...

I do not know about paper patching, you are telling the story so go right ahead and tell it. I have heard though that veggie oil is good also to ease things that shouldn't fit into tight places into...

He said "I" exactly twice. You or Ole Jim and many others may not see things exactly as I do or even see the benefit of many other technical, and time consuming processes in reloading or target...

Banger, I have noticed as I read on this site that it must be your job to criticize most of what other posters opinions or thoughts may be, and you do a great job of it to. Did you ever stop to think...

I have fun shooting, casting, powder coating, I do not have much fun cleaning stubborn fowling from rifle bores though. Maybe you don't mind wasting your time doing so, even if cleaning could be made...

I don't know if there are other shooters here that, like me, believe in and practice the barrel break-in of a new or older rifle by shooting jacketed bullets through their gun barrel and cleaning the...

Looks more like a, on the small side, 4 point. But still nice.

Ken

Bullshop, I would like to offer a suggestion that may help you to improve your shot groups while doing your load development for this project you are working on here. Maybe you are already aware of...

Bruce Drake,

When you have found the load that works best in your rifle, and you are getting good groups, but with occasional fliers, try what Harvey Donaldson suggested in his book "Yours Truley...

Just adding 1-2 table spoons of mineral spirits or paint thinner to either corn cob or walnut media will clean and polished your cases with 3-5 hours in the vibrating cleaner. Polishing additives...

Ohhhhhhhhhhh!

Ken

Fixxah, lighten up, life is too short.

Thanks for your 2 cents, but that does't go very far when buying un-need dies. This suggestion is not ment for some one who would rather only cast and shoot one lube groove boolits or who would...

Chris. I plug my un-needed Star die lube holes with # 5 or 6 shot. I position the shot over the hole to be plugged and with a flat 1/4" punch and hammer, I carfully peen the shot into the hole and...

I for one will not waste my money by buying two dies of the same size, one with 1 row of holes and another with 2 rows of holes. That would be pretty silly.

Lathsmith offers dies with as many as 4...