My mold cast 180 grain flat nose bullet. It worked in the rifle very good and the GP 100. Now the new equation with the 2 inch Kimber. I need a load or google site for a 38 special plus P load for...
Type: Posts; User: wendyj
My mold cast 180 grain flat nose bullet. It worked in the rifle very good and the GP 100. Now the new equation with the 2 inch Kimber. I need a load or google site for a 38 special plus P load for...
Forum: Factory & Surplus Powder
I’ll see if I can find some today. Powder supplies are getting low too.
Forum: Factory & Surplus Powder
So far just the first rounds fired from Federal Fusion ammo. The Hornady muzzleloader bullets I have did load but we’re still tight to push in. I’m thinking the throat is too small and I’m sure TC...
Forum: Factory & Surplus Powder
Emailed EABCO. Maybe they will respond back.
Forum: Factory & Surplus Powder
I’d like to think it was the bullet but after resizing the brass just trying to get it in is a little snug. Goes in but add 2/1000 to it and it sticks about 1/2 way in. I was able to load a 452...
Forum: Factory & Surplus Powder
Now dies are here. Rcbs. The throat appears too small to get a loaded .452 cast without a lot of force. Even the factory was snug and I pulled one and it’s .451. May have to buy a few jacketed...
Forum: Factory & Surplus Powder
I have my own water dropped 45 bullets sized to 452 and lubed with BAC. Bullets weighed out after culled are 460 grain flat nose. Dies should be here today. Lyman 50th doesn't use very many...
Forum: Cast Boolits
What did you use for lubricant to run powder coated bullets through the sizing die.
Forum: Cast Boolits
Murf205. What did you size your cast bullets at. In my Henry 45 I sized to .454. I haven’t slugged this one yet but I have a bunch of 45 loaded up sized at .452 which is what revolver needed. Looks...
Forum: Cast Boolits
Hello, just ordered a 460 barrel for my TC Encore and I cast a 260 grain bullet from a NOE mold. I need another for the 454 and 460. Not sure what these single shots may like. I’ll just use the mold...
Forum: Cast Boolits
My worst was a short barreled Marlin 450 with hot cor bon bullets. Rings your jaw and spine after getting it zeroed. Other would be a 500 smith and Wesson with 2.5 inch ported barrel. Shot 2 shots...
Forum: Factory & Surplus Powder
Conditor22 . That is perfect. I couldn’t have asked for more. I’m shooting it out of a GP100 with a 4 inch barrel.
Thanks so much. I’ll print this and add it to my load books. Again, many Thanks
Forum: Factory & Surplus Powder
I don't need you to spoon feed me anything. I know when the Hornady 10th came out the ELDx was not in the older manuals. I would take a snapshot of the page and send it to whoever needed it. I...
Forum: Factory & Surplus Powder
I would suggest that you try to obtain some manuals yourself, so you won't have to ask often. Using other folks "pet loads" off of the internet can be hazardous if there is any miscommunication or...
Forum: Factory & Surplus Powder
I’d bought a 360-180 mold from NOE. It’s weighing out 185 grains. My Lyman 50th shows no data with exception of Accurate powders. I’m going to use 2400 and cci mag primers. Shot a few through the GP...
Forum: Casting Equipment
I order Lee from Midway and Amazon. 30 days at Amazon return on their dime. They send replacement before you ship yours. Prime only.
Forum: Casting Equipment
I just got one of these from Al. Plan on working up some loads for my GP 100. Figured it should be a game stopper. Don’t have a 357 rifle yet but considering one now with big heavy bullet. Only thing...
Forum: Cast Boolits
I’ve no intentions of loading it hot at all. As stated he’s 81 and can barely hold his guns up to shoot. I won’t blow him up but a squib is biggest concern. I think I’ll stick with the 8-8.5 grains...
Forum: Cast Boolits
I had been loading for my Super Blackhawk and Henry rifle in 45 colt. Got an NOE mold that casts out about 260 grains with my alloy. I’m not shooting either gun as I’ve traded them off. My Father in...
Forum: Casting Equipment
Took it completely out. Cleaned with a small brush and oiled up nice and clean. Still just the NOE and Accurate punches made out of aluminum I think.
Forum: Casting Equipment
Never mind. Seems to be only punches from NOE and Flat punches from Accurate although they did work at one time. Rcbs and Lyman punches are fine.
Forum: Casting Equipment
Not the run of the mill question. I’m having hard time getting top punches in and out of the lube sizer. Been sitting for a few months. Old top punch just fell right out. Tried putting new one in and...
Forum: Factory & Surplus Powder
Picked up some HP38 and Imr 4198. Also 1000 small pistol primers.
Forum: Factory & Surplus Powder
That picture is not what I am looking for but sure would blind a 2 legged critter if it didn't even hit him. I do have a 22 inch barrel but that is a lot of flame.
Forum: Casting Equipment
I have set it lower and higher. Either lube in excess on base or nose. The adjustment works ok. I have a heater under it but that was no help. After using the collet in sizer from NOE and sizing...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |