i have the tumble lube 230 mold as well but I didn't think I could size the tumble lube bullet design
Type: Posts; User: pearcetopher
Forum: Cast Boolits
i have the tumble lube 230 mold as well but I didn't think I could size the tumble lube bullet design
Forum: Cast Boolits
my mistake,
this is the round nose 228 grain normal bullet not tumble lube type
what do you guys load them too?
Forum: Cast Boolits
Hello all,
I have a question about a 45 acp lee boolit
On my 452-230-r I find that in order to allow reliable chambering I have to seat this bullet deep so that it is not touching the...
Forum: Cast Boolits
the hard boolit chambering worries me as I am unable to extract a round properly
if its safe to shoot then I dont really care but I thought the boolit was not supposed to be touching the rifling
Forum: Cast Boolits
Hello all,
I tried casting boolits for my mossberg 464
I used 309 170F lee mold
I ran through a 311 sizer
when chambering I had to give it lots and lots of push to get the bolt to close...
Forum: Cast Boolits
i ordered a whole wack of new stuff
358 sizer
two new primer troughs with update for the load master
2 big *** round ball moulds
Forum: Cast Boolits
Hey guys,
just ordered a bunch of reloading equipment for 357 mag but fogot to order shell plate for lee progressive.
I have about 8 other shell plates in different calibers
has anyone found...
Forum: Cast Boolits
dont size your boolits load them at cast diameter and goodbye keyholing
Forum: Cast Boolits
Hi guys,
I have been casting for a good year now and Ive noticed every once in a while I will have an extreme oversized bullet or undersized bullet that ruins my day
Ive thought about using...
Forum: Cast Boolits
thats a difficult question, I find the 45 acp really likes no heavier than 230 grain
but the 230 grain doesn't have a crimp grove for revolverss
Forum: Cast Boolits
Ill bet your putting the sprues back in the pot immediately cooling it down
Forum: Cast Boolits
HOwmuch petrol did you burn through to melt that down
Forum: Cast Boolits
I didn't know black and decker made pistols
guess you learn something new every day
Forum: Cast Boolits
Ive run into this a bit before too with that same pistol
I find I have to use COAL of 1.065. Mine 6 cav mold drops them at .358 and I load them unsized.
I'm thinking maybe you didnt flare the...
Forum: Cast Boolits
After years of shooting Ive come to the conclusion that revolvers are just more accurate.
Truthfully I cant say why but I can shoot all day with 9mm 40 sw and 45 acp lead or jacketed and be lucky...
Forum: Cast Boolits
ive tried all those things, the load data im using is for the exact rifle, bullet, weight, and powder.
It goes from I think 15 grains of red dot to 22
I can only pull two inch groups at 13...
Forum: Cast Boolits
Hi guys, Ive casted lots of pistol boolits with no issues but I seem to have trouble casting rifle bullets.
I tried the lee 309-170-flat and the lee 311-160-rn both with gas checks attached and I...
Forum: Cast Boolits
Hi guys,
after dealing with an in accurate caliper I finally bought a micrometer and I see my lee molds drop large bullets that I was not sizing because I thought they were at bore diameter, I have...
Forum: Cast Boolits
HI guys,
today at the range I fired my cast 9mm 40sw and 45 acp
I put a few factory copper rounds through them first and found they were patterning all over the place at 15 yards
I switched to...
Forum: Cast Boolits
Ok
Also once I had an accident pre heating the mold and it took a full minute to liquefy on the first pour
Hopefully nothing warped
Forum: Cast Boolits
Hi guys
my lee 6 cav 429 was starting to throw boolit bases that had large peices attached to them. I figured the sprue wasn't closing low enough so I removed it and polished both the bottom of...
Forum: Cast Boolits
jeese arent you reaching pressure maximum with that much powder?
Forum: Cast Boolits
Hi guys, went to the range today firing the lee 355-125-1r rn. loaded to 1.060 with 3.3 grains of bullseye.
Everything functioned fine after firing 250 rounds with no lead in the barrel.
...
Forum: Cast Boolits
ok so I had some lead balls from track of the wolf and I ran them through my tester
the hole it made was larger than my measurer, so I'd imagine the hole size is around 1.2, does this sound correct
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |