Search:

4.2 grains yields 786 fps with the 230. No signs of pressure, etc. I'm probably safe at 4.5. I'll try that next.

Sent from my SM-S901U using Tapatalk

Rex 1 45 Auto. 5" barrel. 230 RN Poly coated

3.4gr 642 fps

3.7gr 690 fps



Sent from my SM-S901U using Tapatalk

I did call Viht. The fellow I spoke with said he had some old load data in a .pdf format that he'd email me. Funny thing is the data he sent does not contain anything for SL.

I will probably just...

Bumping an old thread to see if anyone has N3SL data for 200 and/or 230 grain cast bullets in 45 Auto. Thank you!

Sent from my SM-S901U using Tapatalk

Just on the off chance. Does anyone have Rex 1 data for 9mm? Burn rate indicates it to be Red Dot ish.

I may try 2.5 grains with a 124 and work up from there. But if anyone has some data it...

I loaded a bit of MP240 in 9mm. Gun used is 4.25" commander

4.9 grains with a 124 JHP gave 917 FPS

5.2 grains with 124 gave 1072 FPS

5.5 gave 1120 FPS.

5.5 is maybe showing the smallest...

Anyone have any data worked up?

Sent from my SM-S901U using Tapatalk

Any luck?

Sent from my SM-G970U using Tapatalk

What about sizing and trimming just enough to get a casing to chamber? I imagine you'd be fractionally close to fully sized / cammed over at that point. But it might be just enough to keep from...

Again, the issue with 7.62x39 to 6 ARC is the case taper. Trying to work a new shoulder into the case that's essentially right on top of the taper is likely going to result in a buckled case. To make...

Look at item 933790347 on gunbroker.

Sent from my SM-G970U using Tapatalk

Just a suggestion but I wouldn't trim that short. 1.490" will probably work better. You're going to lose a few thousandths upon firing when the taper is formed out of the case.

Sent from my...

6.5 Grendel is about as straightforward as case conversation gets. Full-length size to bump the shoulder then trim. Trim quite a bit, actually. Without some kind of motorized trimmer it would be nigh...

@chinewalk
@SOFMatchstaff

Any updates on forming 7.62x39 to 6mm ARC? Thank you!

I have been hydraulically forming 7.62x39 into 6mm ARC and have a few extra pieces for sale.

This is quantity 50 large primer pocket mixed head stamp. Mostly Geco and PPU with a few other odds...

If you have any 6.5 Grendel brass you'd part with please send me a PM.

TIA!

Sent from my SM-G970U using Tapatalk

And again

Sent from my SM-A505U using Tapatalk

Up we go. Still looking.

Sent from my SM-A505U using Tapatalk

And again

Sent from my SM-A505U using Tapatalk

Bump. Still looking for a 311359.

Sent from my SM-A505U using Tapatalk

PM sent.

Sent from my SM-A505U using Tapatalk

@johnly

Please empty your inbox. I tried to send you PMs but the system says your box is full.

Sent from my SM-A505U using Tapatalk

PM sent.

Sent from my SM-A505U using Tapatalk

@johnly

Please empty your inbox. I tried to send you PMs but the system says your box is full.


Sent from my SM-A505U using Tapatalk

Nice. They look like a cast version of the Speer Varminter.

Sent from my SM-A505U using Tapatalk