Search:

Roger, I made an adapter to mount to an X-10. I'll get a picture of it for you

Thanks ! I was gonna order the thicker wire. But those look perfect. I'll give them a go. the heavy 247gr 300blk keeps getting hung on the regular Double spring and it's driving me crazy.

Thanks Tyler!
Quick check on McMaster and thinking these. They look to be what you ordered?
https://www.mcmaster.com/9664K55/
(1/2 OD 0.063 wire)
(9.5mm ID)

https://www.mcmaster.com/9664K26/...

good save! removed.



I might just get some from mcmaster carr but the ali ones being all in mm seemed easier. But that slow boat.. .ekk

TylerR

Re springs:
I had mixed results with the regular Double small and large ones. Ended up getting the long Double extension spring and chute and that spring is tightly wound and doesn't sag...

So I sent pictures and called Autonics and apparently it's a big thing to copy and make it look like it. I mean they're all made in China, so specs and function are all the same. And for the cost...

So for those that ebay up the Autonics sensor, any recently got from a quality seller? I have a genuine one but ordered another as a spare from ashleytrade1984* (26900) and it's about as fake as it...

Wanted a nice 300mm base for cases and my only printer that isn't direct drive happens to be my cr10v2 which is the only large enough one for the 300mm base. I used petg and about 2 days and some...

Also one of the guys that printed like crazy took a break and came and back and see how wild things have progressed. Now of course I am printing the 300mm body.. because.. well why not!. I see ramp...

MY D*A*A dropper die fits fine with TylerR's existing drop tubes. No adapters required.

Ah cool. I don't really load those but tried some random 30 cal for the large rifle plate #11. Was on a roll testing them.. That plate changed my life for my cast 300blk subs.

@TylerR I added to the bullet compatibility xlsx for 30 cal using the new clutched collator and the #11 plate.
These are added:
300BO NOE 247-FN
Nosler BT 125gr
Nosler BT 150gr
hornady .308 150...

Overachiever :P Not all heroes wear capes!

Sure! I did test the first version you made of the clutch #11 plate (with supports). works flawless and I'm not opposed to supports. I used my finger to catch it.. boy that was not the greatest idea...

The #11 plate works very well with short bullets too. I ran a bunch of nosler 125gr that are 27.52mm. I have a ton of 150 and 160gr too that I can try as well but so far anything thrown at #11 has...

The Lee never would shoot well for me in my 9" barrels (what I used mostly) And powder coat too (man I skipped over the lube size and gas check life) but I used to stand them up to spray and the base...

I grabbed the 8.5 one. I had printed all my plates with 8.2 so I am curious how these do.



Hah! I bet your filament graveyard is pretty huge!



So they always take me forever to print...

both are pin. printing the slip parts now and should I wait on the plate or the one that's up there now worth starting a print with?

Generated to tighten the shaft parameters. I don't think I changed anything else.
I use NOE HTC310-247-FN-BO3 and 311-247 FN. I actually have a bit of Lee TL309-230-5R still I can test with them as...

I haven't had that issue. I didn't use the plate as generated though. What bullet did that happen with?

I'm definitely down to try that. I use this plate more than anything since I do a lot of blkout. Also gives me a reason to try out the new slip clutch setup.

I'm using Dayton motors. I did both of mine 4mm from the end and 4mm centered. I cheated though and put it in a mill to drill then same as bigmike111 1/8" x 1" pin.

That slip clutch looks like it works really well! How cool is that!!

Got my PRD18-14DN2 in and tested with the original thicker wall drop tuber that gave me issues with the other sensors for brass.. Works like a champ even with jiggling. So indeed not all sensors are...

So excited about the new 2mm wall drop tubes. And I did the one in clear and took some pics and a video. kinda cool to see the infill in there. Might try to light them or something fancy to see the...