http://arsenalmolds.com/image/cache/catalog/310%20SLIVER-%20drawing-500x500.JPG
I had arsenal molds resize the 30hvt to .308 at the nose and .314 at the base. So far I have only tested it with...
Type: Posts; User: Ramson222
Forum: Cast Boolits
http://arsenalmolds.com/image/cache/catalog/310%20SLIVER-%20drawing-500x500.JPG
I had arsenal molds resize the 30hvt to .308 at the nose and .314 at the base. So far I have only tested it with...
Forum: Our Town
Guess I will have to experiment with them.
Forum: Our Town
Only other bit of information I have is that they are led bulbs.
Forum: Our Town
I recently bought a shopping bag sized grab bag of military vehicle small parts for $5.
Two of these led lights were in the bottom of the bag. Can anyone help me ID them and the correct voltage. I...
Forum: Our Town
I have used about every kind of roofing caulk that can be bought. By far the best is called geo cell, it sticks to anything and seems to not be affected by weather at all. I used it 3 years ago to...
Forum: Our Town
Thanks for the help, I had no idea what a cold shut was until now.
Forum: Our Town
Can anyone tell me what the offset hook and the link that mates up with the bracket is called? I would like to make a few sets is there special tools I will need? Bonus points if you can name the...
Forum: Black Powder Cartridge
Thanks toot, looks like we got that one solved. Good thing I did not pay real deal prices for it.
Forum: Black Powder Cartridge
Did Uberti make revolvers with no markings, other than the number right in front of the trigger guard?
I don't think its Uberti all of the Uberti revolvers i looked at have case colored frames....
Forum: Black Powder Cartridge
I have taken pictures of all the marking I can find. Any help with identification and value, will be greatly appreciated. Thanks
Forum: Gunsmithing Tips & Tricks
Sand in a chamber would be a very bad thing.
Forum: Gas Checks
My measurement were taken at the base of the bullet. I will be sending the mold back tomorrow.
Forum: Gas Checks
I measured six random bullets the shank is .286 to .288 at the largest obviously .284 diameter gas checks are not going to fit.
Forum: Gas Checks
Here is a pic of the problem, by the way the maker has offered to replace or fix the mold. Notice the burr around the base of the bullets. 256761
Forum: Gas Checks
I tried everything mentioned and still can not get a gas check on a bullet. I will be sending it back to the maker.
Forum: Gas Checks
Mold is HV 170gr sliver from arsenal molds.
Alloy is 2.21% tin and 6.01% antimony.
Temp is 720F acording to PID.
I'm ladel casting, bottom pour does not work.
I'm preheating the mold on a...
Forum: Gas Checks
I have tightened the pivot as much as possible. Unfortunately there is no sprue plate retainer screw. All there is is a roll pin that serves as a stop for the sprue plate.256322256322
Forum: Gas Checks
I have never had issues seating checks this bad before. Here is a picture of one of the bullets notice the uneven flange around the base. Some of the bullets dont have this problem but checks will...
Forum: Case Forming / Re-forming
Has anyone tried ultra sound gel? Its cheap and slippery and water soluble also.
Forum: Cast Boolits
This ones mine, the fan is a 800sqfm I got from some pot growers. I have a dimmer switch on it as a speed control. When its on full blast I get an complete air exchange in under one minute for my...
Forum: Vintage Ammo
They look a lot like pulled 7.62x54r bullets, what is the diameter? in the picture on the right hand side, at the top of the page you can see the case crimped into the groove....
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |