MidSouth Shooters SupplyRepackboxPBcastcoInline Fabrication
Titan ReloadingRotoMetals2Load DataLee Precision
Reloading Everything Wideners

Search:

Type: Posts; User: Dryb2860

Results 1 to 22 of 23

Search: Search took 0.00 seconds.

  1. Thread: Rollin' Smoke

    by Dryb2860
    Replies
    14
    Views
    2,496

    I have been looking for a reliable source of...

    I have been looking for a reliable source of powder coating and color recommendations that work. I have used Kawasaki Green and it worked great. I used two different reds and blues from Columbia...
  2. Forum: Cast Boolits

    I was long at first and we corrected that problem...

    I was long at first and we corrected that problem by going as low at 1.65 and now I will be going to 1.60, I found some Powder coating scrapings on several cases.
  3. Forum: Cast Boolits

    I will be checking everything you mentioned this...

    I will be checking everything you mentioned this Saturday when the firearm is inspect by a gunsmith. This was my first time loading 45 ACP and I followed the Hodgdon site instructions. I am looking...
  4. Forum: Cast Boolits

    I did a Plunk test and I will say they did ok on...

    I did a Plunk test and I will say they did ok on the seating. I will be looking at going from 1.65 to 1.60 on the seating. I will also revisit the crimp. Thanks, Dennis
  5. Forum: Cast Boolits

    I believe my crimp was good, however I will be...

    I believe my crimp was good, however I will be looking at the total re-load process. My hand is fine. The Hodgdon site has a LRN starting load of 5.4 max load of 6.2 for CFE Pistol. So the cartridge...
  6. Forum: Cast Boolits

    Tar Heel Thank you for your response.

    Tar Heel Thank you for your response.
  7. Replies
    38
    Views
    2,282

    Forum: Our Town

    AS far as I know, as long as the seal holds you...

    AS far as I know, as long as the seal holds you should be good.
  8. Forum: Cast Boolits

    Reload Data for a Lee MOLD 6 CAV 452-230TC using CFE Pistol

    Well I went to the range on Tuesday 07/13/21, and had a miss hap and catastrophic failure in my new Kimber Custom II 45 ACP. I was testing my new loads at 5.6, 5.8, and 6.0 grains of CFE Pistol and...
  9. Replies
    6
    Views
    886

    PID: Looking for a PID Columbia, SC

    I am looking for someone who makes PID's. I am in the Columbia, SC area.
    Thanks,

    Dennis
  10. Replies
    11
    Views
    1,349

    Thanks for the information.

    Thanks for the information.
  11. Replies
    11
    Views
    1,349

    Would a gas check be required with these cast...

    Would a gas check be required with these cast bullets?
  12. Replies
    11
    Views
    1,349

    Mustang thanks. I am looking for a mold to make...

    Mustang thanks. I am looking for a mold to make .224 55gr. I will powder coat faster casting them
  13. Replies
    11
    Views
    1,349

    Thank you for pointing this out. I realize my...

    Thank you for pointing this out. I realize my mistake. I would be powder coating the lead bullet after it cast.
  14. Replies
    11
    Views
    1,349

    .224 55gr FMJ-BT

    I need a little help. I am looking for a mold to make .224 55gr does anyone know where I can get one?

    Thanks,

    Dennis
  15. Replies
    20
    Views
    1,987

    Forum: Cast Boolits

    Thank you and I have been pre heating on a hot...

    Thank you and I have been pre heating on a hot plate.
  16. Replies
    20
    Views
    1,987

    Forum: Cast Boolits

    Thanks. I am getting some good advice here.

    Thanks. I am getting some good advice here.
  17. Replies
    20
    Views
    1,987

    Forum: Cast Boolits

    I stand corrected it is not over sized they are...

    I stand corrected it is not over sized they are over weight.
  18. Replies
    20
    Views
    1,987

    Forum: Cast Boolits

    I stand corrected they are over weight. I am...

    I stand corrected they are over weight. I am using wheel weights and I am see 180 - 185 gr. Using the lee 175 grn. mold.
  19. Replies
    20
    Views
    1,987

    Forum: Cast Boolits

    I am talking about heavy bullets.I am using wheel...

    I am talking about heavy bullets.I am using wheel weights for my casting. I was advised to mix the furnace frequently to ensure my mix is good. I am new to this so any help is welcome. Thanks.
  20. Replies
    20
    Views
    1,987

    Forum: Cast Boolits

    Thank

    Hatch:

    Thank you for your response. I am new to the forum I will try to post to correctly.

    Dennis
  21. Replies
    20
    Views
    1,987

    Forum: Cast Boolits

    Casting over sized bullets

    I am using a Lee Precision Six Cavity Mold .401" Diameter 175 Grain Truncated Cone with a Lee 4 - 20 furnace. I am running my temperature from 750 - 800 degrees. I casting with wheel weight and...
  22. Replies
    6
    Views
    5,456

    Hatch: I am new to cast and reloading. I have...

    Hatch:

    I am new to cast and reloading. I have a Lee pro 4 furnace and I looking for a PID. A friend of mine has one from you and he recommends I contact you for one. Please contact me for we can...
Results 1 to 22 of 23
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check