I cheated on these and bought Hornady HBWC, they have a nice looking lube on them, and they are cold swaged. I shot some with W231 loads from 3.2-3.7 and the accuracy was so-so. My 158gr JHP and H110...
Type: Posts; User: ForneyRider
Forum: Black Powder Cartridge
I cheated on these and bought Hornady HBWC, they have a nice looking lube on them, and they are cold swaged. I shot some with W231 loads from 3.2-3.7 and the accuracy was so-so. My 158gr JHP and H110...
Forum: Muzzleloading.
Doing some lightweight searching revealed Lee REAL bullet at 250gr is the only suitable bullet for CVA. I am still searching as well. I think the CVA documentation says don't go over 250gr lead.
I...
Forum: Black Powder Cartridge
Hodgdon has some load data for black powder for Cowboy load section in their "magazine". I find the magazine in grocery stores and Wal-Mart.
From what I read, you can use FFg and FFFg in pistol,...
Forum: Cast Boolits
I get the flyer from Midway, and several others. What else are you supposed to read on the pot? ha!
Forum: Cast Boolits
Vindictive, malignant and deceitful isn't particular on looks.
Forum: Leverguns
One in our hunting party has a Savage 99 in 300 Savage. It has a rotary magazine, no?
He asked me what it was worth. So I took a look on gunbroker, they were anywhere from 300 to 1500.
300...
Forum: Group Buy Archives
I'm still in.
I might be coaxed into an additional mold for 9mm (~124gr) or 45ACP(185gr SWC or 230-240gr RN).
What's the mold that is flexible for 45 ACP and 45 Colt?
Forum: Cast Boolits
I have the Pro 1000 (has a turret like Lee turret) and Lee Deluxe dies reloading for Springfield 1911 Loaded.
The dies can get gunked up quickly with bullet lube.
Of course, I use different OAL...
Forum: Cast Boolits
You can get rid of the zinc in your wheelweights with silver.
Forum: Cast Boolits
Lead oxides and lead sulphates are common in lead.
I found these 2 resources on Google books. They are free and not too bad a read.
Annual_Report_of_the_State_Mineralogist_.pdf
...
Forum: Classics & Stickies
Has anyone seen this report: Annual_Report_of_the_State_Mineralogist.pdf?
They discuss a number of ways to separate zinc from lead.
Not sure any of the procedures are possible at home. One...
Forum: Cast Boolits
Has anyone seen this report: Annual_Report_of_the_State_Mineralogist.pdf?
They discuss a number of ways to separate zinc from lead.
Not sure any of the procedures are possible at home. One...
Forum: Cast Boolits
My coworker shoots into a berm on his property. He and his kids dig out the lead and recycle. His 9mm reloads are the cheapest to manuf. heh!
Forum: Gunsmithing Tips & Tricks
I have a Timney on my PH 1200.
Shilen makes model 700 triggers too.
Forum: Reloading Equipment
I went with Lee deluxe rifle die set. Full-length die, neck-sizer die, and dead-length bullet seater die(no crimp).
I got the RCBS primer pocket swager for primer crimped brass.
I haven't...
Forum: Group Buy Archives
I got a 6 1/2 in Blackhawk in 41 magnum.
If you come up with a GB on a bullet mold for it, I'd be interested.
I would like a heavy bullet 250gr to 300gr. I can get jacketed bullets 170,200,210,...
I have been reading here and elsewhere and I see to wait some between casting, sizing and seating.
Don't tell mom.
I have been using Frankford Arsenal collet bullet puller for couple hundred pulls. It works good and fast on end of 2x4. But I lose powder with it. I usually end up dumping the...
Forum: Cast Boolits
Marlin 1894 FG (.41 Magnum)
Ruger Blackhawk Hunter Stainless (.41 Magnum)
Desert Eagle (.41 Magnum)
Coonan (.41 Magnum)
Excellent round. S&W still selling models. Taurus is too. Ruger has...
Forum: Cast Boolits
I contacted Alliant Powder about powder load for Power Pistol.
They were very nice and gave me a grain amount.
Forum: Cast Boolits
We get snow every year. No less than .025 inches! Ha!
Yea, my dad just ripped on me for letting the mold cool in the water. He was worried about lead exploding and the mold warping. So I will use...
Forum: Cast Boolits
Not sure on hardness.
This is my first set of water quenching.
The first set I cast, I dropped the bullets on wet towel.
Yep, need to get a hardness tester.
Forum: Cast Boolits
Cranked up the bottom pour Lee pot last night.
I turned the heat all the way up.
The Lee mold gets hot enough to where the mold is too hot for the lead to solidify in less than 8-10 seconds. I...
Forum: Cast Boolits
I had issues myself with CCI primers in large rifle magnum.
They wouldn't go off but are dimpled.
I have no issues with the Federal primers I use in this gun.
I have no issues with the CCI primers...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |