Three years later and mine still looks the same. A thing of beauty.
http://i151.photobucket.com/albums/s121/n8ies/m_PICT0548.jpg
Type: Posts; User: Tom-n8ies
Forum: Reloading Equipment
Three years later and mine still looks the same. A thing of beauty.
http://i151.photobucket.com/albums/s121/n8ies/m_PICT0548.jpg
Forum: Reloading Equipment
I called Hornady about shell plates I bought for my Pro-7 that would not work because they were for the newer Projector press, they told me they would upgrade my Pro-7 to a Projector for $75.00 (I...
Forum: Reloading Equipment
+1 on the oversize primer pockets. Best scrap them.
tom
Forum: Reloading Equipment
Are you getting full travel of the disk?
Make sure it goes as far as possible both ways.
It is not uncommon for the disk to throw a slightly lighter than advertised charge in the table, but ...
Forum: Factory & Surplus Powder
The burning rate would probably be in the neighborhood of 4895, I bought some surplus russian 4895 as it was called, The web site said it is a little slower than 4895 in between or closer to 4064 in...
Forum: Reloading Equipment
I really like my older durachrome dies, glad they are going to take care of you. In the future make sure you are not banging the ram into the carbide insert too hard, that may have been the cause of...
Forum: Reloading Equipment
There was a guy selling replacement turrets with 7/8 14 thread on e-bay for the tru line JR.
Lyman tru-line Junior turret press 7/8-14 die plate item #120339772955
...
Forum: Cast Boolits
I don't understand your post but found a rest you can build cheep.
google "sissor jack rifle rest" and it will show some plans using a car sissor jack for an adjustable front rifle rest.
Here...
Forum: Boolit Lube !
I made some sizing lube from 1 part anhydrous lanolin and 4 or 5 parts 99% isopropyl alcohol.
(iso-heet) dry gas you can get from any auto parts store.
I got the lanolin from eBay. I got the...
Forum: Reloading Equipment
I have been braging them up to all my shooting buddies and people who think they want to get into reloading. Most people turn their noses up when you tell them Lee. The Classic Turret is one press...
Forum: Reloading Equipment
It looks like a place for the handle to go.
My RCBS Jr 3 has an extra hole in the bottom part of the linkage to reverse the stroke I think.
Maybe you take out pin and turn the part with the...
Forum: Reloading Equipment
Where is a good place to get them in bulk for those prices?
tom
Lee hand press kit for 28.00 here
http://www.factorysales.com/cgi/catalog/browse.cgi?1202269038.1737=/html/catalog/rlpress2.html
everything you need but dies.
Take a look at the Lee Classic...
Found a phone number wonder if she has a deep voice? 704-435-9236
tom
Forum: Reloading Equipment
Lee uses Needle bearings very much like those found in u-joints for decaping pins, read it somewhere (Modern Reloading manual by Lee I think)
tom
Forum: Factory Rifles
http://www.savage24.com/
Lots of info there.
enjoy
tom
Forum: Reloading Equipment
I found a phone number on Lee's website under dealer loacater (I think) anyway I googled the phone number and it came back to an electrical contractor type company.
tom
Forum: Reloading Equipment
The RCBS Hammer type puller works prety fast if you use a shell holder instead of the universal collet that comes with the puller. I tried it after somone else posted it on another forum. Works...
Forum: Classics & Stickies
The RCBS Hammer type puller works prety fast if you use a shell holder instead of the universal collet that comes with the puller. I tried it after somone else posted it on another forum. Works...
Forum: Cast Boolits
I have some 200 gr RNFP lead bullets and would like to know if they will work in a 45 ACP. I think they more resemble the 45 colt 250 gr RNFP profile.
Bought them at a gun show so don't know what...
Forum: Hunting with CB's
mix in a spot of Gravox shortly before serving.
Gravox? Is that some new type of rabbit lube?
tom
Forum: Casting Equipment
I made something similar for my soldering iron, 4 square box with a duplex outlet on one half and a light dimmer (with switch) on the other I will have to dig it out.
thanks
tom
Forum: Casting Equipment
Anyone know if he has any more thermometers? I don't see them listed in his store. I would like to get one.
tom
Forum: Reloading Equipment
Not eating a popsicle but did load about a dozen with my eyes closed just to prove it could be done.
tom
Forum: Reloading Equipment
Has anyone tried ideal Yellow 77 Wire Pulling Lubricant? My local Homie Depot did not have GB Wire Aide.
The Ideal 77 is wax based and according to the MSDS it is moderately soluble in water. MSDS...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |