I have tried the boiled peanuts in a can (they are still in the shell) that they sell at Wall Mart, I don't have a taste for them. I prefer dry roasted.
Type: Posts; User: Fretboard
Forum: Cookin' Recipe's
I have tried the boiled peanuts in a can (they are still in the shell) that they sell at Wall Mart, I don't have a taste for them. I prefer dry roasted.
Attended the EIC school, Shot the Presidents, National Trophy, Vintage Springfield, Fun but makes for long days.
Forum: Cookin' Recipe's
Large skillet add water 1cup, cover and bring to simmer, and drain off grease. Steam is hotter than boiling water and cooks faster.
Forum: Military Rifles
Take a look under the butt plate, there is usually a note with the issued person name, the Swiss took those rifles home with them.
Forum: Lead and Lead Alloys
Do a search on zinc, it seems most casters stay away from zinc in the mix because high melt temp,
clogs pore holes fast, cant get clean sharp corners, splatters on impact, hard to cut with the...
Forum: Our Town
Did you get the "State of the State" email from Midway there products may be backordered but they are not raising prices they say:)
Dear Valued Customer,
In the spring of ‘77, I left the Air...
Forum: Our Town
++++++++Prayers sent and fast recovery++++++++++
Forum: Our Town
I tell my kids not to be the first person that goes through the intersection.
Forum: Our Town
Onion syrup
Take two large onions cut in half then slice. Place in fry pan with a little water and cook until the onions start to caramelizes. add just a little more water with two tablespoons of...
Forum: Lead and Lead Alloys
303Guy
Sn=tin, Sb=Antimony, Cu=copper, Pb=lead, is As= Arsenic?
Forum: Lead and Lead Alloys
do you have any pic's of this sludge
Forum: Casting Equipment
Don't have any yet but was thinking of trying the Ove' glove.
Forum: Lead and Lead Alloys
thanks for the read jsize
here is a pic my load, i believe they are all a lead tin mix, as marked lead tin alloy, 76/23 and l5433
they were form a company that made engine bearings.
62109
Forum: Lead and Lead Alloys
I am holding a piece of tin and lead and having a hard time telling the difference.
What are the properties of tin, and my next question is what ratio of tin to soft lead for say 45acp pistol....
Forum: Casting Equipment
Thanks for all the replies, I will try a old hickory handle at least my first experience will smell like a outdoor barbeque.
Forum: Casting Equipment
When my father used to cast fishing lures down the basement over a gas stove he would stir the pot this a thick graphite rod and then use it to scrape the sludge off to the side.
What is the to tool...
Forum: Reloading Equipment
joe,
maybe you can pick up a used 550for a good price, and the warranty is the same new or used
Forum: CB Loads / Military Rifles
Milrifle,
newbie
could you have not just replaced the rear sight with a 100m one? your front sight does look nice though
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |