Blammer is currently doing a gb on the noe boollit 225107 NOE I'm waiting to get one but what i have read from the last run is these itty bitty boolits are great .
Type: Posts; User: 357 Voodoo
Blammer is currently doing a gb on the noe boollit 225107 NOE I'm waiting to get one but what i have read from the last run is these itty bitty boolits are great .
Forum: Our Town
Ive reported them to the FCC three times now because im on the do not call list and i still get calls from them. Ive waited on the line and started to talk to them. Told them not to call again and...
Forum: CB Loads / Military Rifles
Roger here is the link to the discussion thread
http://castboolits.gunloads.com/showthread.php?t=132267
Forum: CB Loads / Military Rifles
Roger,
ES is extreme spread the difference between the fastest and slowest
SD is standard deviation is a statistical calculation
The smaller these numbers are the more uniform the shots will...
Forum: CB Loads / Military Rifles
Gunnut that dont look to shabby! looks like with a little tweeking you could cut your group in half.
Forum: CB Loads / Military Rifles
I shoot about 500 and then i run a patch down the bore and clean the bolt carrier group after each use which is the same as when i shoot jacketed.
I don't have any kind of leading on any part of...
Forum: CB Loads / Military Rifles
Larry Those are the ones that I was using for that target I posted. I've tried 4895 and it gave good accuracy but benchmark out performed it for me. I have yet to try any of the RL powders. I've gone...
Forum: CB Loads / Military Rifles
Dschuttig Im using a NOE gb mould which he has in stock NOE 225-70 RN. When seated to just kiss the rifling with the front driving band it will fill the mag nicely.
Gunnut I have that same problem...
Forum: CB Loads / Military Rifles
Larry the average velocity when I chronographed this load was 2050.
Thanks for the kudos
Forum: CB Loads / Military Rifles
My ar loves the noe 225-70 rn with 20.5 of benchmark behind it
https://lh5.googleusercontent.com/-_bY0pZ2Jpz0/Tt5ObUT13ZI/AAAAAAAAAOg/Phafz62RADc/s400/TgtGfx.jpg
This was shot at 100 yards prone...
Forum: Reloading Equipment
The one range I use to shoot at used blue foam board target backers and toothpicks to hold targets. worked good and lasted for a good long time.
Forum: In Remembrance
today my little brother was killed in a car accented. he was my best friend and my best shooting buddy may he rest where ammo is plenty and the boolit is always perfect.
rest my friend
Sean...
Here is the link to the list of NOE moulds http://castboolits.gunloads.com/showthread.php?t=119487
They are listed under the vender sponsor sales
Welcome
Forum: Cast Boolits
Ash you may want to cut the sprue a little sooner and maybe counter sink the sprue plate a little deeper That should help
Jerry Here is a thread with pics and a description of the bator mould. link
I think turbo has pretty well summed it up but another option may very well be swagging. Than you should be able to have the hollow point and hollow base at the same time.
Forum: Cast Boolits
I did a little bit of testing with this boolit and my best groups came from 13-14 grns of h-4198. with 13.5 being the best. Above 16 grn groups went to patterns. testing was done in two rifles. I...
Forum: Cast Boolits
Ranch Dog has one its 51 grains see here
Forum: Boolit Lube !
I think seagiant is pointing in the right direction but i think it may be just the just the opposite it may be that the boolit is hitting the steep ramp of the XD too soon and slowing the forward...
Forum: Our Town
I have one and for a cheap scope I cant complain. Mine is the 3.5-20x50 varmint and I have it mounted on a rem 700 .223. All tho their not a top of the line scope it is pretty good considering I'm...
Forum: Cast Boolits
Good idea probably much easier than my Allen wrench And i have a few of those nice long skinny tweezers.
Forum: Cast Boolits
If you want heavier than 60 grns than noe has the 22570rn which is very accurate in my ar and bolt gun. there is a group buy right now for it. but the most number of cavity's is 5 but the production...
Forum: Special Projects
Chuck they deform and start shedding small fragments.
mould maker My worry with lino would be if it were too brittle or not. I think the next batch of balls I cast will be out of babbit
Forum: Special Projects
Brass works the best but is expensive. I use ACWW for my ball mill. I change them out after a few uses and remelt.
Unless you need several thousand feet the cost is way to prohibitive. About 10 years ago I worked for a company that made the dies. the cost for a small die with a simple profile was several...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |