PID for regulating oven temperature 1 (only 1) unused and as received from Hatch $115 shipped.
Text for pics.
225-324-4501
Thanks for looking
Type: Posts; User: Hi-Performance Bullet Coatings
Forum: Completed Deals
PID for regulating oven temperature 1 (only 1) unused and as received from Hatch $115 shipped.
Text for pics.
225-324-4501
Thanks for looking
Forum: Coatings and Alternatives
Aqualube will certainly help your sizing efforts. Are you trying to push two bullets thru your sizing die? Magma makes a relieved die and a short die, both should allow a bullet to pass thru on a...
Forum: Coatings and Alternatives
A note on the use of MEK. Here in the U.S. it's getting harder to find 100% pure MEK. A lot of the box stores are carrying a MEK substitute. In my limited experience with the substitute is that it...
Forum: Completed Deals
I have a set of 8 Lyman 457125 500 Gr RN that have been converted by Magma for use on their Bullet Master casting machine. These moulds are lightly used, came from the estate of a gent that used them...
Forum: Coatings and Alternatives
Tazza,
My 2011 is in 9mm and in it's stock form I found it to feel very clunky while shooting it. I prefer a lighter pistol as it swings faster and stops faster on target, What goes back, must go...
Forum: Coatings and Alternatives
I disliked the long dust cover and bull bbl on mine. Trimmed the dust cover, lightened the slide with a BHP cut, tri-topped the slide and lightened it internally. Replaced the bull barrel with a...
Forum: Completed Deals
1960 rds of Turk 8mm ammo on stripper clips in 70 rd bandoleers.
Clean blasting ammo, not recommended for gas guns.
All SPF
192rd Spam can of Greek 30/06 M2 ball on garand clips.
$SPF
Forum: Coatings and Alternatives
TonyN,
Just like the small ovens, it depends on the particular ovens ability to bring the bullet load to temp and it's ability to maintain the temp.
Reliable, repeatable temp control is key...
Forum: Coatings and Alternatives
6bg6ga,
No heat here......I think you may be confusing Hi-Tek Supercoat and industrial powder coating.
Hi-Tek Powder has the catalyst (hardner) built in. Powder must be liquefied with a solvent...
Forum: Coatings and Alternatives
http://i.imgur.com/ww6IgRa.jpg
Here is another target from a gent in Kansas
Forum: Coatings and Alternatives
http://i.imgur.com/frL9U38.jpg
This is the target Avenger442 sent me. Looks like some nice shooting and a very promising load!
Forum: Coatings and Alternatives
Over tumbling will lead to rough looking bullets. 15-20 seconds is all you need, especially in hot weather.
Forum: Coatings and Alternatives
Adam,
Nice job. That bullet should shoot quite well in .38 also.
Forum: Coatings and Alternatives
It will be about 6-8 weeks before that Dark Green Pearlescent arrives here.
Forum: Coatings and Alternatives
For those that may be trying to contact Joe Ban directly, he is having a lot of trouble with accessing the internet. He is in the process of changing service providers and hopefully will be back...
Forum: Coatings and Alternatives
Those were dropped from a Magma Engineering Mould. 115 gr rn
Forum: Coatings and Alternatives
2-2.5 lbs is ok, I wouldn't go much smaller. I am sure it can be done, but I have found that having too few bullets in the container during tumbling makes getting even coatings more difficult.
Forum: Coatings and Alternatives
Unless it is flaking off in big pieces i wouldn't worry about it. I would go ahead and shoot them some flaking shouldn't matter espically at wadcutter velocities.
Your probably too thick with that...
Forum: Coatings and Alternatives
I used a syringe to verify that the measuring spoon I used was indeed 5 ML. I find it easier to use the spoon/dipper in lieu of a syringe, but that's just me.
The powder should be weighed out as...
Forum: Coatings and Alternatives
Ok, try again. I think I fixed it.
Forum: Coatings and Alternatives
https://youtu.be/htv5LFkSEi4
Here is a quick and dirty clip of me doing a first coat of the new dark green.
https://youtu.be/MtfHcAH8hQI
Here is the 2nd coat being applied
Forum: Coatings and Alternatives
197533
This is the Burnt Orange
Forum: Coatings and Alternatives
I only a small sample size of the dark green on hand not enough to list for sale. If you guys are interested in some I have an order pending with Joe and I can see about adding a carton or two to the...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |