Glad to know their quality and customer service. Don't think I'll be ordering anything from them now.
Type: Posts; User: WJP
Glad to know their quality and customer service. Don't think I'll be ordering anything from them now.
Forum: Reloading Equipment
I had fits with one of my 550s one day. Same thing, every primer was about .005 from being flush or below. No matter how hard I pushed it wouldn't seat and the primer wouldn't be deformed any. Long...
Forum: Cast Boolits
Some old faq I ran across. You can change temporarily if you retain old parts and no notification is required. Change it and get rid of the parts will require atf notification. Put a 16 inche+ barrel...
Forum: Cast Boolits
I'd have to dig through some stuff but I don't believe that is 100% true. Permanent changes should be amended with the atf. Temporary changes do not. You just need to retain all originally configured...
Forum: Factory & Surplus Powder
I had a pound of 4320 do the exact same thing. Walked out and saw powder all over the ground to notice the can was about half ate through.
Forum: Reloading Equipment
I've got a couple of those somewhere. Never tried them out though.
Forum: Lead and Lead Alloys
I wouldn't melt it. Shot has been running around $65-$70 per 25lbs lately. Nice score, just load it and shoot it.
Forum: Reloading Equipment
My standard small Dillon bar is set at 2.8 gr of bullseye and is measuring consistently.
Forum: Reloading Equipment
650/750 quick change kits are $160, conversion kits are $115, Dillon dies $125-$140. Roughly $400 each for a complete caliber change. $815 for a new 750. A 550 is $619, conversion kit is $70, quick...
Forum: Our Town
Looks like most new brass to me. I always size and trim new brass.
Forum: Reloading Equipment
I had a similar issue on my 650. If they hand prime ok it may help to make sure your shell plate indexes correct. I had to adjust the black indexer on the left side of the frame. Is your powder check...
Forum: Our Town
I have purchased from him in the past and he was great to deal with. Hope all is well.
Forum: Gunsmithing Tips & Tricks
I think the majority if not all of the AR Stoner 16" are 1/2x36. Pistol/SBR AR Stoner can and usually are 1/2x28. Post a picture of the threads.
Better yet if you have calipers measure and count. ...
Forum: Reloading Equipment
I had one do the same thing. I called and they said it wasn't covered. I did have a couple batteries blow in them and powder check alarms. Cleaned the terminals and installed new batteries and they...
Forum: Special Projects
I'm not saying you can't build what you want if you follow local and fed laws. What I am saying is you can't tell the ffl to change how it's logged or mark it yourself on the 4473. They are logged...
Forum: Special Projects
Correct. When logged it will be receiver in type of firearm in a&d book. In section B 16 you check other (frame, receiver, etc). Section D under type should reflect a&d log/receiver.
Forum: Special Projects
You don't have the option of choosing other, rifle, or pistol on a 4473. Section B of the 4473 is to be completed by the seller/transferee and should reflect their A and D records (How it is logged...
Forum: Single Shot Guns
Must be loosing my mind.or they added some parts in the past month. Thanks for the link. I'm going to see what a fellow member comes up with this week. I like the little guns and Stevens. Really need...
Yes, those are some things to watch for as well as increased erosion due to high temps. Also I personally would not want to run one that hot. You could get close to it's failure rate within another...
Forum: Single Shot Guns
I thought about selling just so I could find the parts. Thanks for the heads up on the changes NoZombies mentioned that to me as well. All I know is it's a Enders Royal Dead Shot. May not be worth...
I know what the little c is. I also know how hot they get after running them. One full auto mag dump on a 90 degree got a titanium can to 719 degrees. Most manufacturers rate them at semi, limited...
https://www.amt-advanced-materials-technology.com/materials/titanium-high-temperature/
Forum: Single Shot Guns
I've got a nice receiver and barrel but nothing else. Does anyone have an idea who may have some parts? I know I could probably buy one cheaper done than fixing this one but I hate to get rid of it...
Glad you found one you like. Be warned not to run it hot. Titanium is light but weakens with heat. So no quick mag dumps, bump fires, full auto, etc. I have a Ti can and love it for my bolt/hunting...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |