Search:

My guess is that there was some dirt in your brass somewhere. I had that happen with some 44 AutoMag brass several years back. I changed out the media and the problem went away.
I don't think...

Great job Frosty :)
Any pics of your pile of Hogs?

I think the eating part has something to do with what they eat???
Here in southern Arkansas, the hogs are pretty tasty, even the big ones.

What is the twist rate on the barrels? I haven't seen it listed anywhere.
Also on their site, they list a 44mag and 45Colt. Not sure if they are available in the US or not...

Are you using open sights or a scope?
If a scope, make sure the base screws are clean and loktited in place.

I ran the numbers through Quickload and this is what it spit out.
Remember this is not load data, just a computer's guess as to what will happen when you pull the trigger
45-70, 500gn Lead 1.242" ,...

My first heater was an old clothes Iron set on a steel plate that the Lyman 450 was mounted to. I'd just plug it in until the body of the luber got warm and the lube started to flow, then turn it...

I put down an Elk many years back with a head shot from a 350gn 45 Colt Ruger Blackhawk travelling around 1250fps. The bullet had a 90% Meplat and was cast of water dropped WW. It punches a perfect...

I used the BPI manual. I looked at the data for 1, 2, or 3 000 Buckshot, then backed off a reasonable amount and tried 4 balls.
I used a roll crimp on top to close it up.
I believe that Federal...

This is the way I did my Swedish rolling block and it turned out great.
I bought an assortment of piano wire at a hobby shop. It came in 3' lengths and was straight.

That 358 African sounds amazing.

My projects for the next little bit is getting a CZ527 223 to shoot well with 50gn tnt Speers. I'm down to about 1/2" groups but I think there's still room for...

I have a Judge and my son has one also.
I load 4 000 buck in a 2.5" hull with 2400 powder.
With 45 colt loads, it's reasonably accurate. Guaranteed I could hit a goblin at 25yds.
My son got the...

I have the Weigitinny on my 45 Blackhawk and like it.

I have lubed and sized the ranch dog bullets in my Lyman 4500.
If you have the Lee's, you'll just have to try it and see how they go.
Give me a call if you need any stick lube...
For cleaning out...

Well...
Now I need a new mold.
See how you guys are...

Looked like lots of fun!
I have some Russian hp ammo. I've never shot anything with it yet...

I used a Tromix Linear Comp. It directs the muzzle gasses forwards. I've got them on my 7.62x39, 450bushmaster and now the 358 Razorback.

6# is great for an AR10 sized platform.
I didn't...

324518
It shoots reasonably well, but I think it wants to do better, lol.
I picked up some shim stock and I'm considering swimming the barrel extension or bedding it with loctite 620...

It locks back now!
I switched magazines and it locked back. So I took the first mag apart and stretched the spring and it locks back on that magazine also.
Once ir was running reliably, I dialed...

Rapier- Is that the 358MGP that you are running?
Is that the Lee 358-200 powder coated in the picture?
How fast can you run the PC Lee bullet and still get good accuracy?
I gave it a quick try,...

324485
Ok, the new borescope came in.
I put the adjustable gas block on and it's lined up with the port.

Thank you very much for the detailed information.
I'll check all of that and try again.

Now I can't find my bore Scope :( It only worked with my phone from 5 years ago...
Got on Amazon and ordered a new one...

As close as I can tell with Quickload, the gas port pressure at 9" is between 10-12kpsi for the 200s and 180s.

The lower is new as well. I will try it on a different lower to see if it runs there.

The gas key is tight.