Search:

Or bought sub-standard stock cheaper: or didn't check the dimension. Poor quality control, at least. Or deliberate planned obsolescence?

Picked up a used Lyman 450, missing lube top cap, stuck hard with hard lube, picked up set of spares for 4500, including new ram and handle assembly.

It seemed LOOSE: Brown & Sharp 0-1 mike says...

I've got a 38, husky, threaded muzzle... The Swiss Products K-31 Muzzle Break happens to be the same thread... This break also has reputation as a bbl de-resonator, improving accuracy, but likely...

How do you get copper in the lead? Powder? Source? Quite a different melting point. have COWW and antimony, soon to cast up samples to get exact size. 1942 Husquvarna, excellent condition.

I've...

Loading for a M39, want to use .311 Sierra SMK 174 gr, and new powder,

What collet size needed to pull (assuming .310?) factory 188 bullets, recomendation on a puller, plan also to load

NOE...

Thanks, Gearnasher: Built a set of stairs and handrails last year, all very old Hard Yellow pine, much FULL of resin. Burned up couple of 55 gal bbls of the chips!

Have numerous scraps, so will...

2nd attempt. Top punch lyman #?

I had a small order, med flat rate box, via UPS w/ USPS final, arrived Mon at a midway
UPS facility, left Fri. Three days of sitting time. Box taping was re-done. No powder/primers, just a few...

For 6.5 x 55 Swede, need top punch information. Plan on casting ww@ to start, threads on this site suggest problems with soft metals

Thanks

Gunsnammo has Finn 39's, getting pricey, but getting scarce. Picked up a 1970 that is as close to mint as can be. "sneak" finn 39's were match conditioned, bedding, trigger work, and used only for...

Question on length: don't have a sizer yet, likely Lyman or RCBS, Is length a possible problem?

Sign me up: 4 cavity, gas check, all pins.
kendwell at surfglobal dot net

Please put me in for a 4 cavity with all pins. Looks like a good alternative to the 314 @ 180 gr I missed out on, for Finn 39.
kendwell at surfglobal dot net

edited for right model #, ? is suitability, and how big a sizer needed also, want for 9mm luger.

Picked up 2 ea double cavity 9mm ballisticast H&G 51? (not in hand,) which need sprue plate and hardware, and no handles. .361 stamp, guess that's the nominal die size,
seems a bit big for the 9mm...

One .359, all pins, Handles?,
kendwell(at)searchglobal (dot) net

Update to all available pins, small, large, penta and flat

I'd also prefer 2 cav, but will take 4 cav, penta and plug pins, .432, and handles

kendwell@searchglobal.net

Kendwell, In for two (2) #2 too!

Another formulation is Silikroil. Two other products of interest are Kreen and Microil.
Recommend all. Rebuild of 1977 Ford 4wd F250 and maintenance for 12 years of a 1973 Torino was made possible...

Picked up gew 88 bbl from Numrich, described over the phone as in the white, and take off from new receiver. Has good rifling in center of bore, but worn badly in chamber, and no rifling at all...

During late 60's, I resized a lot of '06 brass to 6.5. Seems I recall there is a difference between SAAMI spec and Swedish Specs, for some reason?

Anybody know or can check if this will feed/function in an ak-47? I'd like to see a heavier bullet with a hollow point for hunting.

Swede: pg 2, 3, and 4 on the closed 314 129 gr ak group buy returns a "404, page not found error code." should have mentioned that in 1st message. I assume the shipment is incoming?
Anyways, happy...

Confirming for 4 cavity with 1 HP. , and handles. Folks, my computer skills very slow

kendwell