Search:

I am looking for a youth roundball load, something like a trap load of green dot of about 14 gr with a .575 lee roundball . It does burn clean and leaves no residue. It needs to be light enough for...

thanks for this info

thanks
I looked through some posts and used 7.5 gr trail boss felt wad, corn meal with room left for ball, crimped 454 lee. Went 10/10 on gong at 35 yrds. thats good enough with shotgun bead for me....

I came into a short lane adapter 20ga-45 colt/410 scavanger smoothbore. So no rifling. I tried some factory cast cowboy loads (250 gr )I had laying around a while. They did not shoot accuratly. So...

I would like to cast a few 20-1 220g gc 9.3 to be fired at 1700ft/s and 350 gr ranch dog at 1300 f/s

target is deer at much less than 100 yards

question is will they mushroom at all at that...

They where a good deal at $100
but have not seen them so cheap In a long while
extractors are availiable periodically ebay $30
do not load without the required clips and the extractors should not...

try tin a bit soft, but makes beautiful boolits

Also the Browning Lever youth is really neat, but I found the lever too hard for a child to easily work.
The decent little savage is this one Savage 13700 CUB 22S/L/LR AT YOUTH not the rascal or...

cz scout is a great little gun. But I haven't seen one in years. For a really small girl I would look at the one of the little savage rifles with a thumb hole stock and peep sight and are drilled...

since the server change

anyone else have trouble posting on rfc for the last month or so. Can log in, just not post. thanks

just bought 44lbs in large ingots, with foundary stampings for $88 delivered to my door. I am wondering if I should by the other 150lbs he has

Finally casts some RD 366 boolits designed for the 9 Makarov. With Lyman #2 and a very hot pour, came out at .3675 and are about 90gr (haven't weighed them). Would like to try them in a 9.3x62 over ...

ordered some 9.3 specific gas checks a few months ago, finally cast some boolits and was impressed with the new checks. Unlike the 375 checks which are commonly used, no more concave or convex...

anyone using this mold, does it feed well in 1911's? Hardness suggestions? thanks

I am interested in how the new 9.3 checks work out.

just drug the old girl out an put in new springs (gunslinger) and some space aged grease and it is smooth as all get out. Almost too smooth. Does anyone have any loading advice. it seems to hang up...

anyone have any experience with them. I think they are make in Japan by Miroku. do they function well, trigger. would you recomend one? found one in 357 $7XX.

have recently moved up to 50 grains of 3031 under a 225g checked boolit. Hope to have a chance to shoot some tommorrow.

I had the same problem with partizan brass. Ordered a second rcbs shell holder and very gently dremmeled the open up the shell holder. Took off only a few hundreths of an inch.

My questtion is just how long lead remains in the air as a vapor. My guess would be not very long, so unless you are eating lead sinkers it should not be a problem. Mercury vapors are also very bad...

I have read lots about varrious methods of heat treating and soft points. I was wonding if a wide deep HP of Lyman could be filled with soft lead to create a Partition of sorts or would the lead just...

If I can still get in. I would like

RG4 2pb 2 GC

I just molded some of your 6.5's and they really look great.

I really like the looks of my new noe mold. great looking 6.5 boolit. I to am looking forward to suggerstion of a good load. I am leading towards 5744

will this design feed slick?