Search:

Alloying Zinc with about 3% tin makes for a easier casting. I managed to cast awesome Lyman 356637 in a 90gr Zinc bullet as well as a HP NOE 124gr that was 75gr as a HP 9mm going 1800 FPS. In a...

Is it not allowing you to change turrets? Would like to see this in action. Gives me an idea for my pro 1000

Your the man! Great idea bud! Ill see if my buddy Willie will try it

-Eagle Eye

Hello BHuji, I was having this issue also and I noticed you mention W231. My load is very similar as I am using two tumble lube bullets that are PC lee 124 TC tumble lube boolit and the NOE TL135...

Hello, I currently worked up a load with the NOE 309HTC 153-SP mold using HP38/W231 powder.
@ 11grs Im getting consistant sub MOA grouping

https://youtu.be/85nBPXXcU8w

Results show at 13:00...

Hello, I wanted to drop a suggestion as I read you are looking for a replacement for the 30-06. I've been testing a cast load using the NOE 309HTC NOE-153-SP mold on the 30-06, Its a non lube grove...

Right on! Thats some great results with this round. My ol' man use to paper patch this round. I spent hours helping him when I was young. Brings back memories seeing others shoot this.

Lol, Surprisingly these recoil a hella lot less than any 9mm FMJ round i've shot even at 7grs. HiPoints might be able to survive these rounds

Interested in your Lube A Matic. PM sent

Funny you've mention. I was wondering if I epoxy or glue a steel ball bearing inside the HP and see what that does may get level 2/3 AP fragmenting round? Might be cool to try out

Hello Casters and Reloaders, and Merry Christmas.

For those who are wondering if Cast ZINC (ZN) b00lits hold true at longer distance and not tumble and key hole. I just uploaded a short VR on this...

Thanks parkerhale1200, Well ive tried casted Foundrytype lead and didn't get results using those powders I mentioned and also H335 and H4895. Maybe as we get up there in BHN these bullets are brittle...

Actually I started with If, else statements and ran the relay in series with the Lee thermostat for thermal runaway protection. Found that it runs extremely accurate that way also. So far ive been...

Actually if you price out the parts like I have comparing both Johnny Reloading Bench write up. It is CHEAPER. You dont have to buy a project box. And like I've mention you can re purpose old...

MT Gianni is correct. Also Temps vary between pots. What I do for me at first is crank the pot to 8 untill it melts throughly. Flux with saw dust then dial down to 5, Wait for it to cycle then go to...

HBN is a micron coating (little goes very far) and is heat resistant up to 2k F. The testing ive seen so far, claimants have stated it helps eliminate vertical deviation on cold bore shots and also...

Hello Casters and Reloaders,
I wanted to share my project I've created. I set forth in a journey to create a more accurate PID controller for our lead pots that can be modified to user preference...

Cast 223 at 2310 fps avg. Fun out to 300 yards. Almost half the powder and the same cost of 22lr

My second choice is 300AAC 230gr subsonics.. really makes steel ring

Man thats great info Thank-You! I have a 2 cavity Lee 356-124 mold ill try opening the sprue hole up. That may solve the Zinc casting fillout issue.
Here are some close up's on the Lee 356-124 zinc...

Ok will do. Ill shoot a IPSC 66% target at 100 yards freshly painted. Its got combat sights so Ill do my best lol My 300aac rings it everytime and thats 95grs

Haha ya I spaced out about shooting the steel. Check out my (Cast Zinc rounds fame or Fail) playlist. Its on my Part 3 (24:50). Also im shooting the Lee 126gr Tumble lube TC bullet in zinc which is...

RogerDat,
I saw that. He expiremented with zinc alloy PB which increased hardness. Zinc DOES clean your barrel. A friend of mine uses zinc low charge rounds as a barrel clear out before shooting...

Hello OS OK, and thank-you very much for all the positis-em. I created this round in liu of watching Elvis Ammo's results. As I too are an avid listener to his channel. You're very correct about the...

Casting with zinc is very challenging even with aged casters that have tried. I'm having to laddle pour them using a Turkey fryer and getting a good fill can be challenging. The hardest part is you...

Yes your right, theres many new things to try out on cast bullets and coatings those willing to expirement should post. I want to try HBN coating on cast powder coated bullets as it allows more...