Search:

Have you tried measuring a pulled boolit from one of your loaded cases? If I was to guess, its that you're swaging them down somewhere in your loading process. Could be the crimp die even if your...

I'm pushing the lee 170 gn at 2400 fps. I don't really think its necessary to go that hot, but its working for me. I'm getting 1.5'' groups @100 yds.

The only hunting show I'm all that interested in is "Meateater" on the sportsman channel.

https://www.youtube.com/watch?v=O-lyk1WyyJ4

https://www.youtube.com/watch?v=wAnbDvLIAac

https://www.youtube.com/watch?v=TwX9mJvss1k


I don't suggest anyone actually try this.

I haven't seen small pistol primers since Dec. I've managed to get a couple pounds of every powder I use and a couple thousand large rifle and large pistol primers.

You can definitely fill a 230 gn hole but thats about it. I have one but I don't use it. Kind of a useless item. Super tiny and super thin.

First things first i would measure the diameter of a pulled bullet from one of your "crimp the hell out of it" cartridges. If that's not the issue, you could try using a bit softer alloy and a...

I use a 30 carbine funnel in my Lee powder dies for .30 rifles with cast bullets. You can buy the individual part off the Lee website. Works great. There is a long thread here on this exact issue...

I've never had a problem with Midway. I always price shop everything. If i can get a better deal from Amazon Prime, Grafs, Natchez, etc., thats where my money goes. I find that most of the time...

its just a matter of filling out the form and sending it with a check or credit card #. You also have to mail a copy of the same form to your chief law enforcement officer (generally the sheriff),...

Unique and 2400. If I can choose a separate category for rifles, 4198 and 4895. These are the only 4 powders I use so its not really a difficult choice. I like to keep my component selection as...

I use the six cavity Lee 356-125-2R. It works well for me. Feeds well in every gun I've shot it in, plenty accurate. I'm normally shooting it in a Ruger SR9c

Works fine in Glocks as well FYI.

The small pocket brass is pretty handy to have on hand when you run out of LP primers. Its also a PITA when they get mixed in with your large pocket brass. I haven't seen any difference in...

I'm using 4.5 gn of Unique with the 356-125-2R bullet.

Also the barrel in my buddies' CW-9 has standard rifling. I believe all of Kahr's economy guns are like that.

Its an 8 inch in line fan from Menards. I believe it was $36. They sell smaller ones, but i picked the 8 inch because it had a much higher CFM rating. Its in the ducting aisle. All the fittings...

Here's what i came up with. It's certainly not a professional installation and i did this in like 25 minutes, but it works. I hung it with nail in romex straps and big tie wraps. I am going to...

Thanks a lot for this info, Ben. I've been searching the web for several hours looking for a powder through expanding die for 30-30 and '06. I have no experience loading rifle cartridges, but it...

Hey thanks for the info :drinks: I just took your advise and went to menards yesterday to check out the ducting stuff. I picked up an 8in inline fan with some reducers for 6in. I made a...

I'm pretty new to reloading and casting, but i think i have a pretty nice set up so far. The bench is made of 4x4's and a solid oak table top (it weighs like 150 lbs and is rock freaking solid) I...

Same here. I'm pretty new to this, but the yields on the WW make it more of a hassle than range lead. Plus range lead is free.