Search:

KONUSPRO 3-10X44 #7255
I have one on each .375 H&H as well as one on each .458 WinMag rifle for a total of 4.
they take all the recoil I can give them and have yet to shift POI.
My heaviest load...

If you are wanting super slick feeding as well as great accuracy and tremendous impact with deep penetration from a n M48 Yugo, might I suggest Accurate Molds #32-210C in the gas check version,...

I am using the following mold with a full charge of WC867, I get 1980 fps in a Yugo M48-A and nothing has yet got up off the ground and complained.
NOE# 326-258-RN-BQ4
257756

Top to bottom:
Weatherby Vanguard Dangerous Game Rifle .375 H&H
CZ 550 Safari Classic .375 H&H
Winchester 1894 Chief Crazy Horse .38-55

257755

I would like to take a moment to thank you all for your replies, and to ask you to keep chiming in as the thoughts grab you.
I am going to go with the 5744 loads for light loads and am going to try...

I have two beautiful new moulds that I am unable to find load data for. The powders I plan to use are AA2520 and 5744.
The moulds are: 1) RCBS.378-312-BPS and 2) Accurate Molds #38-345AG
The...

Everything but the Load Lookupworks. I must admit, I am quite bummed! I was hoping to find data for my 2 new moulds. .378" 312 gr PB spitz and 345 gr GC spitz

A matched pair of CZ 550 Safari Classic rifles, 1 in .375 H&H, and 1 in .458 Win Mag.

I know that you are looking for a heavier bullet but as a suggestion, I've been getting excellent accuracy with the following:
Lyman #311359 (Gas Check)115gr
Top Punch : 359
UPC #2660359
75%...

I use an RCBS case form / trim die to make mine from once fired range pick up brass, annealed before forming.
I have worked up the following loads for my Arisaka. ( Gas checked and sized to .314" )...

I have developed the following loads for the 1891 Argentine Mausers that I own. One has been sporterized a bit and the other is full military configuration.
All loads have proven accurate in both...

I use this bullet for feral pig, mule deer, and elk. The lack of meplat has not hindered the performance in any way.
My alloy throws a .3132" bullet and I size to .312" with RCBS gas checks and...

I've not seen an answer to the thread from 2010:

"Top Punch for 215 Karabiner lee boolit
What top punch is everyone using for this bullet -- 8mm. Will use either a lyman or rcbs punch for my...

The load I have settled on is:
Lyman #314299 sized .314", Winchester 7.62x54R brass, Remington 9 1/2 M LRM Primers
3.0 gr Alliant 2400 under 48.2 gr WC867 ( not yet chronographed )
After walking...

You are going to want to get a LEE Universal Case Expanding Die if you don't want to damage your bullet during seating.

I have been using Lee products since 1978 and have only encountered 2 problems.
The first one was my fault, because way back then, I didn't know about case neck turning so my collet neck sizer had...

Cartridge Load Information
~~~~~~~~~~~~~~~~~~~~~~~~~~
Load Name: 8x56R LEE Cast 205
Bullet Mfg: LEE C329-205-1R
Bullet Type: Cast
Bullet Lube: Lee Alox
Bullet Size: .330
Bullet Weight: 205...

1978, LEE Loader .30-30, LEE 150gr GC single cavity mould, (casted and sized the night before at my off-post apartment), IMR 3031 using the scoop that came with the kit.
Loaded and fired at the...

This is the load I use.
(Please remember [I]loading safety procedures[I] if you decide to try this load!)
Case head expansion mikes out to less than Remington factory 200 gr loads in my Marlin 336....

I run Windows 7 Ultimate 64 bit on 3 different computers at my home, (yes...I am a gamer, gunsmith, shooter, reloader).
I Have 2 1TB HDD's in all of them, (non-raid configurations).
I played around...

You may want to try these guys, it is where we get our targets.
http://gttargets.com/targetsandbases.htm

I always use Lyman's flash-hole deburring and primer pocket uniforming tools on all new and once-fired Privi-Partizan brass prior to loading.
It is a one-time operation.
Calibers used:
.223 Rem,...