I can count on one hand the number of people that were interested.
My source was only interested in selling a large number of them...
Type: Posts; User: jason867
Forum: Group Buy Archives
I can count on one hand the number of people that were interested.
My source was only interested in selling a large number of them...
Forum: Group Buy Archives
I'm not getting the response I expected. So this buy is cancelled.
Forum: Group Buy Archives
No, I was quoting a statement from my source.
When I wasn't quoting, I changed the adjective so it would make sense.
If I had money to buy their factory, I'd be keeping the brass for myself......
Forum: Group Buy Archives
Straight from my source:
I am going to offer you guys $0.50/pc. On the brass, so if you would like to buy some directly, that is what I'd charge you also. It is FOB Bensenville, IL. So whatever...
Forum: Group Buy Archives
EDIT: I'm not getting the response I expected. So this buy is cancelled.
Like the title says, I may be able to get some bulk (as in more than 100K pieces) 7.62x54R new reloadable boxer style brass...
Forum: Reloading Equipment
I did contact lee, and they sent me, for free, an expander plug made for 38S&W. It's a little wider (the width I figured I'd need actually) and goes in a little deeper as well.
I tried it out and...
Forum: Reloading Equipment
having knocked the carbide ring out of the lee fcd, this makes it a conventional taper crimp die, no?
Forum: Reloading Equipment
Say I got the 38/357 m die and it worked keeping my 358 boolits at 358. Wouldn't running them through the FCD with the carbide ring squeeze the bullets back down to 355?
Or should I get a 38/357...
Forum: Reloading Equipment
The expander for a 38 is too short for use with 9mm.
I didn't want to screw up my 38 adjustment so I didn't bother trying. I might try it if I don't find a better solution and I need more girth...
Forum: Reloading Equipment
I understand that, but how do I get a bigger one?
Forum: Reloading Equipment
My gun is actually a Bersa Thunder 9mm.
I know glock recommends not shooting lead through their barrels. But from what I've read, seen, and experienced, its not something to worry about.
As I...
Forum: Reloading Equipment
I've been doing a lot of searching and research, but I haven't found any satisfactory answers, or if I did I didn't realize it because of information overload.
Anyways, I'm reloading 9mm luger...
Forum: Cast Boolits
The bullets start out between .358" & .360" at the rear band, as cast. usually slightly oblong.
After seating, crimping, and pulling back out, they measure about .357" at the rear band.
But...
Forum: Cast Boolits
I'm not concerned about bullet movement, I've never had a problem with it yet.
I'm concerned about the slow powders burning properly.
Regardless, I think I've got a good grasp of what a heavy...
Forum: Cast Boolits
Your opinion contradicts the general consensus, from everywhere I've looked, not just here at cast boolits.
I've looked at several forums and have noted many people, including several who seem to...
Forum: Cast Boolits
Well I'm applying the crimp with a lee factory crimp die. As I assume you know, it also sizes the whole cartridge. As far as I can see there is no bulging going on...
Also, I don't size the...
Forum: Cast Boolits
Here's two examples of some crimp that I applied to a 38sp and 357mag.
The silver 38sp has significantly more crimp than the brass 357mag.
So which is considered heavy or strong crimp? I've...
Forum: Cast Boolits
I appreciate everyone's opinions and experience on here. I kinda knew I'd have to experiment to find out what works for me, but having some discussion on it kinda helped clear my head and motivated...
Forum: Cast Boolits
I know I'll probably get a lot of different opinions on this, but I figured it couldn't hurt to ask.
According to Lee's reloading book, one should cast their bullets to a certain hardness, for a...
I neglected to mention on here that I settled on the following recipe.
140gr Lee LSWC, cast with wheel weights air-cooled, alox tumble lubed. Dropped from mould at .3585 or so, so no need to size...
Forum: Shot Loads For Pistols
Well, I ran out of cast bullets to reload so I set about creating my own shot shell, in .38sp.
It's not as nice as the original poster's stuff.
I primed a winchester .38 shell with a federal...
Hello! New member, longtime reader!
I picked up this mold because I think my taurus 85 ultra lite likes lighter bullets than standard 158s. Unfortunately my lee manual doesn't have this bullet...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |