Search:

Thanks.

I searched for micro disc on their site.

“ No products were found matching your selection.”

Prayers sent

Does anyone have a Lee Pro Auto-Disk Powder Measure Micro Disk they would be willing to part with?

Thanks!

326181

If you wind up in Tennessee you’re welcome to try out mine. I’d be really tempted by a lever action 327 as well!

I’m not sure. I mainly loved the formula because I can measure shot cups and calculate the diameter that should fit before buying a mold. If the pellets cause pickle bumps bad enough, there will be...

Loud! Fun. Versatile when you consider all the shorter cartridges that work too. No regrets other than I wish I got a larger frame/longer barrel and seven shot model. It’s whitetail capable in my...

Welcome to the forum!

They look frosty to me. Better than wrinkles and poor fill out. Do you have more clues to what alloy you are using? Are they hard with a lot of antimony? Do they ting...

Talk about stink!
A dead snake stinks worse and sooner than other dead critters in my opinion. What a mess to have to clean up!!!

This discussion about getting the die to close further is part of a discussion about using the die for a cartridge different from what it was manufactured to work on.

Cheaper than having a custom...

I took a paper midway catalog to a widows yard sale years back. I offered 1/2 of then current new prices for used stuff. Helped her determine the value of some other stuff.
Some dies for a 357/45...

Would it work to grind open the gaps wider on a Factory Crimp Die to make it crimp deeper/smaller diameter?

Main thing I don’t like is the price tag. Next is factory rounds use 0.355” bullets instead of 0.357”

Weren’t the maximum revolvers discontinued because of all the commotion about top strap...

The Lyman 5th edition copyright 2023 also contains data for Vihtavuori N310 powder in 12 gauge. 7/8 ounce, And 1 ounce loads on page 149 and a 1-1/8 ounce load on page 150.

Every burn rate chart...

My BPI 10th edition copyright 2016 has 21 bullseye loads for 3/4 ounce loads on page 173.

Tightwad, WAA Lite and E3 are faster than bullseye on the first burn rate chart I pulled up online...

If I ever felt the need for using cast in 223, I would go to the Berger bullets website and play around with their stability calculator using the 1 in 9 twist rate for your example. I would select a...

Bullseye is pretty fast, but there are some faster powders used in 12 gauge.

Think you had some compression in the 9mm wasp load? Or less than the 38? I went back and read the first post for the...

So this is strange. It seems like as the case volume decreases the need for powder significantly decreases

Yes. And chamber pressure sharply increases! That was one of the features with my 200...

Slug your bore is the standard answer around here.

I’ve been lucky with 0.001” over jacketed diameter.

It’s expensive, but number two tungsten shot (18 gram per cc) is another option. The consensus is it performs like shot 4-5 sizes larger, so it won’t be quite to #4 buckshot effective, but there will...

Some single phase motor have start and run capacitors. My attic fan needs a start capacitor. If I take a broom and spin it, it will take off and run.

Found it! Load No. 26 where the TUWGL12 is listed on the update page.
All of the components are currently available. Fantastic!

I’d like to see the mold and some boolets from it.

Well, how did the pressure tests go? Were the results what you expected?

Good morning Ms MaryB
When you say older are we talking carburetor old? I assume it’s got fuel infection since you mentioned an electric fuel pump vs a mechanical fuel pump. Do you know about what...

Further testing revealed a boolet sized to 0.358” will chamber. I went back to the original 1.2 grain charge but reduced the oal down to 1.110” AND switched to RMI brass I purchased new for this...