Search:

Yes, like Duerva said. I doubt any shooter here is good enough to see any difference offhand at 100+ yards.

You still need a BP lub, but I powder coat LEE REAL 3 times to increase diameter. Make them fit tite in the barrel for the best accuracy. This works much better than putting aluminum foil in the mold.

You can't beat 170 grain Remington Core lock factory ammo for 30 30 deer. The cheapest and worry free part of a hunt.

Tell Der my Saco Finish Mosin blows away any other rifle in my collection, any I have a lot of them.

Just dip the mold in the pot. Boolits come out nice and frosty so powder coat is better.

Waste of time to trim and sort by headstamp. You won't notice any difference. Just shoot it until it splits.

Scrap the junk poor quality GI 06 brass. The primer pockets all not always centered and break depriming pins. Factory 06 brass is all over the place. Buckets of once fired at my club range.

Put the cases in a loading block and go up and down the rows with large prick punch. I can expand 50 in about a minute.

It's a no brainer. I adjust and check the scale with a 30 cal. Sierra Match King bullet. They are exactly 168 grains. They also will shoot under 1/2 inch out of my Savage model 12 varmint rifle.

Go with a LEE Promelt 20 pound bottom pour. You get at least three times the production and better quality with bottom pour. None of the top of the pot slag you get and have to keep skimming with top...

Hi fcvan. I went to the Dragon Man when I was out your way. What a Museum. Me too with Unique for 9MM. Shoots lights out in my CZ TS Orange.

Nosler partition. Why risk a trophy shot with a cast bullet. Ammo is the cheapest part of a professional hunt.

I **** caned the ladles 30 year ago I got my first bottom pot. A lot faster with better quality. Not all the crud from the top of the pot.

Baltimoreed dos not know how to use the Lee collet die. I have loaded thousands and thousands of cast boolets for mil-surplus rifles with the best results. Most accurate and fastest to use with a...

A bottom pour Lee 20 pound pot is the way to go, especially with 6 cavity molds, Ladle stinks. Too slow and you get all the **** from the top.

Bottom pour 20 pound lee pot is the way to go, especially with a 6 cavity mold. Ladle stinks. TOO SLOW and you get a lot of **** for the top of pot.

Go with the 6 cavity LE mdi said. I shoot 200 to 300 each time with my CZ TS.

I have shake and dumped thousands of boolets on a parchment paper and bake on a cheep toaster oven. Some way overthink it.

Thanks bubba 50. Can you recommend a accurate target round ball load for the 1 in 48 twist?

I bought a used barrel for a TC Hawken. It has a low SN 19xxx , deeper rifling, no black powder only warning ,and an iron cross stamp under by the breach. Does anyone else have one like it and knows...

I usually shoot cast in my war beaters with iron sights, but I bought a Savage model 12 bench rest in 308. It shoots lights out with 168G Sierra Matchkings. Trying 180G lyman with powder coat and...

Has anyone noticed better accuracy with a certain brand of gas check over another? Are Hornady better than Gator or Blammer for accuracy?

Same here with the front sight. Used a 03 Springfield high one. Crest117 did you cronny. your 32.5 H4895 load? Has anyone used toilet paper for a case filler?

I would appreciate any recommendations loading my original trapdoor 45 70. I have been using 20G of 2400 with no filler and a LEE 405 G tumble lubed with 45/45/10. Accuracy is better when boolit...

Should powder coat scratch off with a thumbnail? The reason I ask is that I am getting leading in the first inches on my pistol target loads in 45 ACP and 9MM. I am using HF red and they pass the...