Anyone using the R&J locking handles on their moulds? If so what do you think of them, and have they made your mould sessions any easier?
regards
Type: Posts; User: delta1
Forum: Casting Equipment
Anyone using the R&J locking handles on their moulds? If so what do you think of them, and have they made your mould sessions any easier?
regards
Forum: Hunting with CB's
Ah yes tenderloins frying in the pan with onions, nothing better. Well done sir.
Forum: Our Town
The Tom Gresham article is a good read and 100% right in my opinion.
Forum: Cast Boolits
What I am finding is that I cannot stay logged in. The little check box is half covered by advertising and will not let me check it off.
I am in need of a copy of both the Manual and instructions for the Lyman45 lube sizer. Just to make sure I set it up right and all parts are there. I have yet to receive it, so trying to get all them...
Forum: Cast Boolits
I see velocity increase in some of my black powder loads that were under to much compression. When I backed off in powder but kept the compression die the same, velocity increased and the es and sd...
Forum: Black Powder Cartridge
That was quite an intersting article, looks as though curtis and harvey at least in the seive testing rated very high. first time I had ever heard of the Diamond powder though.
Forum: Black Powder Cartridge
Don:
lot # is BPL15A It would be nice to see a stickie on the difference in powders, granulations, and powder cans [ect]. Or maybe I just haven't read through everything as of yet.
...
Forum: Black Powder Cartridge
cajun shooter,
Thank you for that, gives a little more insight into the workings of B, and why the difference.
Forum: Black Powder Cartridge
Any idea as to what years this container was used for CH packaging?
Forum: Black Powder Cartridge
This one of my CH containers it is in 500G weight and says
Manufactured in Germany for
Nobel Explosives Company Limited
Stevenston, Ayrshire, Scotland
A subsidiary of Imperial Chemical Company
...
Forum: Black Powder Cartridge
Well that sounds great. Gives me another reloading road to go down and have fun with.
Forum: Black Powder Cartridge
Is that in burn rate only since it is smaller in size than Goex 2FF
Forum: Black Powder Cartridge
I have a few pounds of Curtis and Harvey F granulation. Can anyone give me an idea of the granulation compared to other black powder. The reason I am asking is it says F on the bottles which I assume...
Forum: Black Powder Cartridge
Thank you for the numbers. Looks as though I could use any of them. Next will be to see how they work out at distances past 200 yds. I can do 700 here at the house and the temps to stay reasonable,...
Forum: Black Powder Cartridge
Ben"
The best I can do for powder here is Goex FFG. I have 6# of Goex cartridge I have been hoarding. and have 5# of 1F Curtis and Harvey but it seems finer in granulation compared to Goex 2F....
Forum: Black Powder Cartridge
My next test will be by adding an extra .030 wad. just to see if the extra compression will tighten up the SD. Although the 67 grain load is very close to what I am looking for. What seems to be odd...
Forum: Black Powder Cartridge
Well here is the first round of trying to get a closer ES and SD let me know what you think so far and what i should work on next if anything.
Started with a clean bore by running a dry patch to...
Forum: Black Powder Cartridge
Don:
Are you saying I should be patching between shots?
Forum: Black Powder Cartridge
I shall give it a try one item at a time.
Forum: Black Powder Cartridge
I will give it a whirl and see what happens. Sure do wish the old eyes were about 60 years younger though.
Forum: Black Powder Cartridge
Don:
Will do that, from what I read it should be in the single digits. Will these speeds and a mid range vernier tang get me out to 700 yds? Thats as far as I have here at the house.
Forum: Black Powder Cartridge
Well now to try them at ranges beyond the 200 yd mark. And try and tighten up the sd a little bit.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |