100% agree.
JSIZEMORE, Keep in mind the 22rf targets are made of very thin steel. The 22rf targets, even though they are the (large) 1/2 size target, they are much thinner than the 1/2 size...
Type: Posts; User: Chill Wills
Forum: Rimfire Area
100% agree.
JSIZEMORE, Keep in mind the 22rf targets are made of very thin steel. The 22rf targets, even though they are the (large) 1/2 size target, they are much thinner than the 1/2 size...
Forum: Cast Boolits
I have more than one lead pot so I can dedicate each pot for the alloy needed but I do empty them now and then and simply pour them out over the top (side) into ingot molds. Just like pouring out a...
For Lyman, look on ebay and check Brownells if you haven't yet.
I have no experience with the Willians, sorry.
Forum: Rimfire Area
I play the 22rf lever rifle silhouette game. About 25 years worth. The CCI standard velocity are a very good choice and much better than the Mini Mags. For those of you that don't know, it is a 100...
Forum: Reloading Equipment
Here is the picture of the ones I make.
Forum: Leverguns
That mold has been very good in my Carbine. I would like to find a rifle (length) replacement for shooting lever silhouette.
Forum: Black Powder Cartridge
:bigsmyl2:
"a ringed barrel approximately 1-1/4” in front of the rear sight"
Ooops! It clearly said rear sight but in my mind, I saw front sight. I'll go sit in the corner now.
Forum: Black Powder Cartridge
You can also have it cut back and re-crowned.
I have a Colt 25 ACP. I have dies and a mold. 15 or 20 years, I have not even started to reload the empties.
Feel free to pass along any tips to load the littlest semi-auto.
Forum: Reloading Equipment
Additional data added:
Bullets sized to 0.452"
The first diameter I expanded the sized cases to 0.452" and as expected, it did not show any bullet reduction. I did this as a baseline.
Bullets...
Forum: Reloading Equipment
I made the expander.
Bullets sized to 0.452"
The first diameter I expanded the sized cases to 0.452" and as expected, it did not show any bullet reduction. I did this as a baseline.
Bullets...
Forum: Reloading Equipment
I think that it is possible that in some cases, the factory die set expanders put too much “squeeze” or neck tension, on the cast bullets we often use, reducing the diameter smaller than optimal for...
Forum: Lead and Lead Alloys
Yes. When that bullet gets where it is going, that is a combination that will move a lot of meat out of its way. Something like it was killing big buffalo when the first cartridge rifles came on the...
Forum: Casting Equipment
That is a puzzle. Maybe cut with Tool Steel. Hmmm, ......not sure.
Forum: Lead and Lead Alloys
Have fun. You will do fine.
Having done the same, I found that there are many right ways to do it, but if you more or less have equal or more parts Tin to Antimony in the mix, the bullet will hold...
That is my bullet and powder choice for my Rem. 700 Classic too. It has been very good in both accuracy and killing power.
I'm not Doug, but mine pined 0.429" pass, 0.430" hold. one held 0.429" Maybe it would be more accurate honed out. Not sure.
As said, the trigger is as good (very good) as anything I have or...
It is not a problem, (really!) but I wasn't asking for loading data as much as wondering if "Universal Clays" had a good track record for accuracy in the 45 Colt. See post #1, paragraph 1, last...
Forum: Muzzleloading.
ROA animation
Here is the link....
https://www.youtube.com/watch?v=nWNM7HxgaQE
I have the Remington 700 Classic in 35 Whelen.
Jacket or cast. Low power variable scope.
It is the bolt action survival rifle here at my place.
Yes. Clays is not the subject of this thread of posts. It turns out, if you go back an read from post #1, it can not be repeated enough based on how many times the two are confused.
Thanks! Based on this, I will make some test loads to put on paper at 25 yards. 7grs to 9 grs., at every half grain, and go with the one that looks best. Just what I was looking for.
There is a powder "Clays" that is fast like Bullseye. Universal Clays is not the same. You would not want to confuse the two.
I am asking if you have good advice (experience) about Universal Clays...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |