I got it figured out, thanks!
Type: Posts; User: montanamike
Forum: Our Town
I bought a pid from him awhile back and have a few questions. Does anyone have an email or phone number I can use to contact him?
Thanks
Forum: Lead and Lead Alloys
Usually when I fire up the pot it's to do 1000+lbs
Forum: Lead and Lead Alloys
ive had this happen, before i got a PID. I figured out the lead gets substantially hotter the lower it gets. I'm assuming its oxidizing faster the hotter it gets. It quit happening when I started...
Forum: Lead and Lead Alloys
I had this problem once. How wet is the newspaper? I found out I wasn't soaking the newspaper long enough. the boolits that hit closer to the edge of the bucket where the paper had more water in it...
Forum: Lead and Lead Alloys
If it's been drying for 13 years I think you're good to go.
Forum: Lead and Lead Alloys
I tried 20 to 1 lead tin with a hollow point boolit and got great expansion but some leading. So i tried ww with a little tin and still got leading. I had to add a little foundrytype to get the lead...
Forum: Lead and Lead Alloys
Some of the older weights I have with a little steel zinc in them average about 70% lead. Hopefully you have the same ratio.
Forum: Group Buy Archives
Any idea when these will be shipping?
Forum: Lead and Lead Alloys
That's what i use for full house 44 mag loads, 45acp, 357, 45/70. Great all purpose handgun alloy
Forum: Group Buy Archives
I'll take a 6 cavity aluminum with traditional lube groove
Mike - 2005 at live . Com
Forum: Lead and Lead Alloys
I had about 1/2-3/5 55 gallon drum of foundrytype and it weighed 996 lbs so I would guess each barrel would be between 1700-2000 pounds
Forum: Gas Checks
I've used NOE copper checks and sages aluminum checks. Both work well on my 440 lee mold.
Forum: Lead and Lead Alloys
If there is any zinc in the range lead don't worry. Melt it all down. The fraction of a percent will make no difference.
Forum: Lead and Lead Alloys
You'll be fine as long as you didn't leave it sit Too long.
Forum: Lead and Lead Alloys
It's just dross stuck to the bottom of the pot.
Forum: Cast Boolits
Fully prep'd 1500 pieces of lc 556 and stainless tumbled 6000 223/556 mixed headstamp. And just worked on organizing the gun room in general.
Forum: Lead and Lead Alloys
25# pure 5# super hard and 1.5# tin is almost exactly Lyman #2 which will be right at 15bhn.
Forum: Lead and Lead Alloys
Got it all in the shed. Gonna take awhile to melt it all down...
http://i1142.photobucket.com/albums/n617/mtmike/Mobile%20Uploads/Resized_20170609_193717.jpeg
Forum: Lead and Lead Alloys
So I picked up the rest of the weights today! I think I was a little off on the weight but there is probably 11,000 pounds or so. I know these are producing at least 70% recovery so we'll see what I...
Forum: Lead and Lead Alloys
I use 2/2/96 (not water dropped or heat treated) and h110 for full house loads and get no leading what so ever without a gas check. you should be fine.
Forum: Lead and Lead Alloys
just melt em down like regular weights. just make sure they are dry first!
Forum: Lead and Lead Alloys
it makes a huge difference when you have a lid. Also, anyone thinking about using a pot of this size should buy the highest btu burner they can find. the bayou classic 55,000 but is barely enough....
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |